Results 41 to 50 of about 638,978 (319)
Study of Erosion- Corrosion Behavior of Aluminum Metal Matrix Composite [PDF]
Engineering and Technology Journal, 2014 The aim of present work is to study the erosion –corrosion behavior of aluminum metal composite which consists of the (Al – 12wt % Si) alloy as matrix phase and 10wt% SiC particles as reinforcing phase.
Muna K. Abbass +1 more
doaj +1 more source
Ultrasonics Sonochemistry, 2022 The effect of compressive stress on cavitation erosion-corrosion behavior of nickel-aluminum bronze alloy was investigated, and the results showed that the alloy exhibited selective phase corrosion of eutectoid “α + κiii” and its destruction was ...
Zhenbo Qin +6 more
doaj +1 more source
Erosion-corrosion maps for carbon steel in crude oil/water slurries : impact angle and applied potential effects [PDF]
, 2010 In studies of erosion-corrosion, there have been few investigations into the effect of tribological issues, such as particle impact and impact angle, on erosion-corrosion of materials in oil field production.
Stack, M.M., Abdulrahman, G.H.
core +3 more sources
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Crystals, 2021 Two kinds of Ti-alloys, i.e., Al–5Ti and Al–10Ti alloys, were manufactured in this study, and their ultrasonic cavitation erosion behaviors in 3.5 wt.% NaCl solution were evaluated by the cumulative mass loss, scanning electronic micrograph, and three ...
Jingtao Zhao +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley +1 more source
Applied Sciences, 2022 The presence of CO2, sand, and water in oil and gas reservoirs causes erosion–corrosion leading to material degradation in pipelines and fluid handling equipment that results in increasing maintenance and repair costs and a decrease in production.
Muhammed S. Parancheerivilakkathil +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Architecture‐Driven Sensor Stability in Weft‐Knitted Engineering Textiles
Advanced Engineering Materials, EarlyView.Textile‐integrated sensor architectures are systematically compared to evaluate their electromechanical behavior under combined mechanical and environmental loading. Pocket‐based integration exhibits stable and reproducible signals, whereas tunnel‐based routing shows higher sensitivity accompanied by increased variability.
Adnan Maroof Khan +5 more
wiley +1 more source