Results 41 to 50 of about 322,364 (304)

Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy

Advanced Engineering Materials, EarlyView.
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley   +1 more source

Corrosion characteristics of X65 steel in CO2/oil/water environment of gathering pipeline

工程科学学报, 2018
The corrosion behavior of X65 steel in the CO2/oil/water environment of gathering pipeline was investigated by mass loss, X-ray powder diffraction (XRD), scanning electron microscopy with X-ray microanalysis (SEM-EDS), and electrochemical analysis ...
CHENG Yuan-peng, BAI Yu, LI Zi-li, LIU Jian-guo   +3 more
doaj   +1 more source

Effects of Carbon Nanoparticles on Triboelectro‐Induced Surface Defects

Advanced Engineering Materials, EarlyView.
Carbon nanoparticles added to grease modify the electrocontact behavior. The synergy of particle concentration and electric current dominates the surface damage of metals in contact. Electrical surface damage caused by current leakage is a critical challenge in high‐performance applications such as electric vehicle (EV) drivetrains and wind turbine ...
Mohsen Tajedini, Lu Fang, Jacob Bons, Mohammad Humaun Kabir, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

Utilization of Natural Extracts as Corrosion Inhibitors in the Seawater Environment

Jurnal Rekayasa Kimia & Lingkungan, 2021
Infrastructures in coastal area are mostly made of metal which is susceptible to corrosion due to direct contact with the seawater. The Seawater greatly affects the corrosion rate of metals because it contains chloride ions which can penetrate metal ...
Pocut Nurul Alam, Cut Meurah Rosnelly, Justaman Arifin Karo karo, Akhar Ilhamdi, Raiyan Soekarno, Izzan Nur Aslam   +5 more
doaj   +1 more source

Optimizing Post Friction Stir Welding Heat Treatment in Dissimilar Friction Stir Welded 6061/AlSi10MgMn Joints for Electrical Vehicle Battery Housing

Advanced Engineering Materials, EarlyView.
Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld aging between 170°C and 220°C enhances hardness uniformity within the nugget zone.
Emanuele Ghio, Emanuela Cerri
wiley   +1 more source

Study made of corrosion resistance of stainless steel and nickel alloys in nuclear reactor superheaters [PDF]

, 1967
Experiments performed under conditions found in nuclear reactor superheaters determine the corrosion rate of stainless steel and nickel alloys used in them. Electropolishing was the primary surface treatment before the corrosion test.
Greenberg, S., Hart, R. K., Lee, R. H., Ruther, W. E., Schlueter, R. R.   +4 more
core   +1 more source

Role of the reversible electrochemical deprotonation of phosphate species in anaerobic biocorrosion of steels [PDF]

, 2007
Sulphate reducing bacteria are known to play a major role in anaerobic microbiological influenced corrosion of steels, but mechanisms behind their influence are still source of debates as certain phenomena remain unexplained.
Alain Bergel, Albery, Angell, Beech, Belay, Brennenstuhl, Bryant, Canhoto, Chan, Chen, Ciszkowska, Crolet, Crolet, Da Silva, Da Silva, Da Silva, Daniele, Daniele, Daniele, Daniele, Daniele, Fonseca, Hamilton, Hamilton, Harms, Hernández Gayosso, Heyrovsky, Iverson, King, King, Lee, Lee, Lee, Leonardo De Silva Muñoz, Marinović, Marinović, Mc Leod, Molina, Nielsen, O’Neil, Pankhania, Rajagopal, Rao, Régine Basséguy, Sand, Santana Rodríguez, Stojek, Takehara, Videla, Von Wolzogen Kühr, Yang, Yashiro, Yu, Yu   +53 more
core   +3 more sources

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Predicting the Corrosion Rate of Steel in Cathodically Protected Concrete Using Potential Shift [PDF]

, 2019
The commonly accepted Cathodic Protection (CP) criterion i.e. 100mV decay evolves from experimental investigations and may not always be accurate. Alternatively, corrosion rate monitoring can assess the adequacy of CP.
Ganjian, Esmaiel, Goyal, Arpit, Khorami, Morteza, Olubanwo, Adegoke, Sadeghi Pouya, Homayoon   +4 more
core   +1 more source