Results 71 to 80 of about 329,330 (354)
Corrosion. Corrosion Rate of Thermal Sprayed WC Cermet Coating.
Journal of the Society of Materials Science, Japan, 1999 The corrosion rates of thermal sprayed WC cermet coatings in 0.05mol/dm3 sodium sulfate solutions at pH 1.0, 6.5 and 12.0 have been measured using AC impedance method and quantitative analysis of the solutions. The cermet coating films were made of WC-Co, WC-Co-Cr and WC-Cr-Ni powder matrials by the high velocity oxygen-fuel spraying method.
Yasuyuki TAKATANI +3 more
openaire +2 more sources
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
Advances in Materials Science and Engineering, 2015 The long-term corrosion rate of X80 steel in an acidic red soil was monitored in situ by using a precise electrical resistance (ER) test system. The corrosion characteristics of X80 steel were examined via SEM, EDS, and XRD.
Shuaixing Wang +4 more
doaj +1 more source
Iraqi Journal of Chemical and Petroleum Engineering, 2019 Corrosion rate tests were carried out on carbon steel under concentration cells conditions of oxygen and sodium chloride. The effect of aeration in one compartment on the corrosion rate of both coupled metals was determined.
Muayad F. Hamad +4 more
doaj +1 more source
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
A Machine Learning-Based Model for Predicting Atmospheric Corrosion Rate of Carbon Steel
Advances in Materials Science and Engineering, 2021 The purpose of this study is to develop a practical artificial neural network (ANN) model for predicting the atmospheric corrosion rate of carbon steel. A set of 240 data samples, which are collected from the experimental results of atmospheric corrosion
Ngoc-Long Tran +3 more
doaj +1 more source
Triethylphosphite as a network forming agent enhances in-vitro biocompatibility and corrosion protection of hybrid organic-inorganic sol-gel coatings for Ti6Al4V alloys [PDF]
, 2014 The biocompatibility and life of metallic implants can be enhanced through improving the biocompatibility and corrosion protection characteristics of the coatings used with these materials.
Barranco, V +5 more
core +3 more sources
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Journal of Applied Engineering and Technological ScienceThe development of environmentally friendly alternative technologies, such as seawater batteries, is increasingly important in addressing energy needs.
Rezza Ruzuqi +5 more
doaj +1 more source
Study of corrosion of 1100 aluminum [PDF]
, 1967 Corrosion of 1100 aluminum in oxygen-saturated water at 70 degrees C under experimental conditions was studied, emphasizing effects of exposure interruption, the number of specimens, and the refreshment rate. A logarithmic equation was derived to express
Draley, J. E., Loess, R. E., Mori, S.
core +1 more source