Results 21 to 30 of about 2,463,852 (291)
Corrosion Resistance of Trip Steels [PDF]
Corrosion, 1975 Anodic polarization tests on certain metastable austenitic (TRIP) steels having very high strength and good ductility, with contents of sulfur, phosphorus, and other impurities comparable to those of commercial alloy steels, indicate they would have about the same general corrosion resistance as commercial Type 316 stainless steel and appreciably ...
Baghdasarian, Ara, Ravitz, S.F.
openaire +2 more sources
Excimer laser treatment of ZE41 magnesium alloy for corrosion resistance and microhardness improvement [PDF]
, 2010 We would like to acknowledge the financial support of the ‘‘Conseil regional de PACA’’ and Protection des Metaux d’Arenc). The authors are grateful to PMA’s engineers Ms. E. Castellan, Ms. A. Gonthier and Mr. F.
KHALFAOUI, Walid +3 more
core +1 more source
Erosion-corrosion behaviour of Zirconia WC-6Co, WC-6Ni and SS316 [PDF]
, 2015 The current study investigates a ceramic, two cermets and a metal under solid-liquid impingement with 3.5% NaCl and 150mg/l hydraulic fracturing sand at two extreme angles of impact, 90° and 20°.
Giourntas, L. +3 more
core +3 more sources
Effects of Cold Rolling on the Corrosion Resistance of 2205 Duplex Stainless Steel in Artificial Seawater [PDF]
Cailiao Baohu, 2023 In order to clarify the change of the corrosion properties of 2205 duplex stainless steel in artificial seawater after cold rolling，2205 duplex stainless steel was cold-rolled at different reduction rates (PCRR ＝20%-80%)，and then the sample was ...
GUO Yu, ZHANG Yu-xin, SONG Hang, CHEN Ji, WANG Hong-chen, PENG Qi-qiang
doaj +1 more source
Tribo-corrosion mechanisms of stainless steel in soft drinks [PDF]
, 2010 Tribo-corrosion mechanisms of 316L Stainless Steel in slurries containing common household soft drinks have been studied through investigating the micro-abrasion-corrosion performance using a ball and disk apparatus which has been modified to measure the
Stack, M.M., Hodge, C.
core +4 more sources
Materials, 2022 Chloride-induced corrosion of steel rebars is one of the major causes of the premature failures of reinforced concrete structures served in different environments. This paper investigates the semiconducting behaviour and corrosion resistance of the passive film formed on the corrosion-resistant rebars exposed to simulated concrete pore solutions with ...
Lv, Shanglin, Li, Kefei
openaire +2 more sources
Journal of Materials Research and TechnologyThe preparation of biodegradable pure Zn porous scaffolds using additive manufacturing technology has great potential for application. However, the mechanical properties of pure Zn are not sufficient for the clinical application of stents.
Chengzhe Wang +3 more
doaj +1 more source
Corrosion resistance of composite nickel-AlO deposits
, 1999 The corrosion resistance of composite nickel electrodeposits with alumina embedded in the nickel matrix prepared in sulfate and chloride bath has been studied. As corrosion environment salt spray and nitric acid solution have been tested.
P. Vassiliou +3 more
core +1 more source
Journal of Materials Research and TechnologyThe microstructure evolution, cyclic oxidation, and hot corrosion behavior of the unheated-treated (As-built) and solution + double aging (SDA)-treated Inconel 718 alloys fabricated through laser-induction hybrid cladding (LIHC) were investigated. It was
Lei Qin +7 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source