Results 211 to 220 of about 15,676,159 (315)

Dendrite-scale quantitative evaluation of solidification cracking in welding using in-situ synchrotron X-ray imaging: distribution characteristics of critical strain. [PDF]

Sci Technol Adv Mater
Kitano H, Nagira T, Yoshinaka F, Sawaguchi T, Yamashita T, Aoki Y, Fujii H.   +6 more
europepmc   +1 more source

Development of Automatic Crack-tracing Apparatus and its Application to Corrosion Cracking and Fatigue Crack Propagation

CORROSION ENGINEERING, 1982
Shiro Yoshizawa, Koji Yamakawa, Shunichi Yonezawa, Osamu Tsuji   +3 more
openaire   +2 more sources

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

MCL-YOLO: A Multi-Module Collaborative Lightweight Object Detection Method for Bridge Crack Detection. [PDF]

Sensors (Basel)
Han B, Wu Y, Feng W, Mi X.
europepmc   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Durability Degradation Mechanisms and Coupled Deterioration Behaviors of Geopolymer Concrete Under Multi-Hazard Service Environments: A Critical Review. [PDF]

Materials (Basel)
Li J, Yang F, Hai R, Mi W, Hui C.
europepmc   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Experimental Study on Crack Evolution Law of a Full-Scale Prestressed Concrete Beam Based on Fractal Theory. [PDF]

Materials (Basel)
Jiang Z, Wang B, Liu H, Zhang J, Zhou J, He H, Wei H, Zou J.   +7 more
europepmc   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source