Results 201 to 210 of about 28,118 (298)

A rubber-based sensor with over 100 million-level ultra-sensitivity (0-10% strain range) via 3D super-interface. [PDF]

Nat Commun
Wang X, Huang Y, Wang H, Yin S, Xu C, Wang Z, Chen Y.   +6 more
europepmc   +1 more source

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Advanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang, Mayur Pole, Tingkun Liu, Kenneth A. Ross, Christopher B. Smith   +4 more
wiley   +1 more source

Interaction between an embedded crack and an interface crack in nonhomogeneous coating system

, 2005
Paulino, GH, E.E. Theotokoglou, Glaucio H. Paulino, Theotokoglou, EE   +3 more
core   +1 more source

A Comprehensive Experimental and Finite Element Analysis Study on the Bonding Strength Evaluation of Wafer-to-Wafer Hybrid Bonding with Polyimide Film Dielectrics. [PDF]

Micromachines (Basel)
Mei C, Zheng T, Ding Z, Zhang D, Xu Y, Zhao H, Chang L, Hu Q, Xia C, Liu S, Li L.   +10 more
europepmc   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Crack interaction in magnetoelectroelastic materials

, 2014
Yonko Stoynov
core   +1 more source

A Microplane Constitutive Model for SFRC Subjected to High Temperatures. [PDF]

Materials (Basel)
Ripani M, Vrech S, Caggiano A, Folino P.
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

The Effect of Ultraviolet Modification on the Performance of Polyamide Fiber-Reinforced Cement Mortars: Optimization and Characterization Using Response Surface Methodology. [PDF]

Polymers (Basel)
Akarsu Özenç A, Mardani A, Özenç F, Eren S.   +3 more
europepmc   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source