Results 11 to 20 of about 236,901 (237)
Kinking of a Crack Out of an Interface [PDF]
Journal of Applied Mechanics, 1989 Kinking of a plane strain crack out of the interface between two dissimilar isotropic elastic solids is analyzed. The focus is on the initiation of kinking and thus the segment of the crack leaving the interface is imagined to be short compared to the segment in the interface.
Ming-Yuan He, John W. Hutchinson
core +4 more sources
A Criterion for Crack Kinking Out of an Interface [PDF]
Key Engineering Materials, 2008 Cotterell and Rice theory (1980) on the kinking of a crack submitted to a biaxial loading in a homogeneous material has been recently revisited (Leguillon and Murer 2008). The mixed criterion for fracture which involves both an energetic and a stress condition (Leguillon 2002) allows defining a positive threshold of the T-stress below which no ...
Leguillon, Dominique, Murer, Sébastien
openaire +3 more sources
Application of Interfacial Propagation and Kinking Crack Concept to ECC/Concrete Overlay Repair System [PDF]
Advances in Materials Science and Engineering, 2014 Research on the application of ultraductile engineered cementitious composite (ECC) as overlay in the repair of deteriorated concrete structures is performed in this paper. Also, interfacial crack kinking and trapping mechanism experimentally observed in
Yaw ChiaHwan, Li Wei
doaj +2 more sources
Materials & Design, 2020 To study microscale fracture behavior under mode II and mode III loading new sample geometries are proposed. Finite element simulations were carried out to determine the mode I, II and III stress intensity factor distributions over the sample width as ...
J. Ast +4 more
doaj +1 more source
Paths of interactive cracks in creep conditions [PDF]
Fracture and Structural Integrity, 2015 The paper contains plane strain analysis of uniformly stretched plate working in creep condition. The plate contains initial defects in forms of central and/or edge cracks working in mode I.
K. Nowak
doaj +2 more sources
Materials & Design, 2022 Al-12Si alloy processed through additive manufacturing exhibits a complex hierarchical structure. At the mesoscale, its melt pool boundaries constitute a network of weak interfaces that provides preferred pathways for crack kinking, leading to both ...
M. Jamshidian +3 more
doaj +1 more source
Journal of Materials Research and Technology, 2023 The induction of long-period stacking ordered (LPSO) phase through heat treatment was an effective method to strengthen magnesium alloys. In this study, the volume fraction of lamellar LPSO in the Mg-4Gd-1Zn-0.5Mn alloy was controlled by optimizing the ...
Shiyu Luan +4 more
doaj +1 more source
Microscale Mapping of Fiber Strain and Damage in Composite Wrinkled Laminates Using Computed Tomography Assisted Wide-Angle X-Ray Scattering. [PDF]
Adv Sci (Weinh)This study combines full‐field tomography with diffraction mapping to quantify radial (ε002$\varepsilon _{002}$) and axial (ε100$\varepsilon _{100}$) lattice strain in wrinkled carbon‐fiber specimens for the first time. Radial microstrain gradients (−14.5 µεMPa$\varepsilon \mathrm{MPa}$−1) are found to signal damage‐prone zones ahead of failure, which ...
Luong HM +7 more
europepmc +2 more sources
Kinking conditions for running cracks [PDF]
Le Journal de Physique IV, 1994 The problem of the abrupt change of the direction of a crack, propagating with high velocity, is studied in the present work. The study is based on a unified approach of the directional instability phenomena, which accompany running cracks. According to this approach, the running tip is simulated by a prebranched configuration, consisted of two ...
Andrianopoulos, N., Kourkoulis, S.
openaire +2 more sources
Effect of temperature on crack kinking and jumping in a cross-ply laminated beam
Archives of Mechanics, 2016 To understand the mechanisms of crack kinking and jumping that occur within the 90° layer of a cross-ply fiber reinforced plastic laminated plate, double cantilever beam tests were performed at several temperatures for laminated plates with two types of ...
S. Yamamoto, T. Ikeda, A. Senba
doaj +1 more source