Results 111 to 120 of about 68,107 (316)

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Characterization of crack nucleation in TA6V under fretting-fatigue loading using the potential drop technique [PDF]

, 2010
Crack initiation in a Ti-6Al-4V alloy was investigated experimentally in fretting fatigue conditions. A cylinder-plane geometry was used for the contact, and partial slip conditions were considered.
Deyber, S., S. Deyber, Kubiak, KJ, J. Meriaux, Kubiak, Krzysztof, Fouvry, S, S. Fouvry, Meriaux, J., K.J. Kubiak, Meriaux, J, Deyber, S, Fouvry, S.   +11 more
core   +1 more source

Static experiment on rapid crack bifurcation with Y-shaped and parallel notches

Mechanical Engineering Journal, 2016
Static experiments related to rapid crack bifurcation are conducted with PMMA plate specimens with Y-shaped notches. The bifurcation angle of the Y-shaped notch is changed from zero to 45 degrees.
Shinichi SUZUKI, Yusuke IWASAKI, Yasunobu SHIMIZU, Mohd Azrin BIN YUSOF   +3 more
doaj   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Nondestructive Testing of Welded Composite Metal Foams

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva, Aman Kaushik, Afsaneh Rabiei   +2 more
wiley   +1 more source

Design and analysis of welded aircraft wing panels [PDF]

, 2005
Nowadays, increasing manufacturing cost effectiveness becomes a vital condition for the commercial success of the next generation of large wide body aircrafts.
Theos, Athanasios
core  

Influence of nano-inclusions' grain boundaries on crack propagation modes in materials

, 2011
The effect of nano-inclusions on materials strength and toughness has attracted great interest in recent years. It has been shown that tuning the morphological and microstructural features of materials can tailor their fracture modes.
Karakasidis, TE, Charitidis, CA, Charitidis, C. A., Karakasidis, T. E.   +3 more
core   +1 more source

Investigation of Crack Propagation and Failure of Liquid-Filled Cylindrical Shells Damaged in High-Pressure Environments

Journal of Marine Science and Engineering
Cylindrical shell structures have excellent structural properties and load-bearing capacities in fields such as aerospace, marine engineering, and nuclear power.
Hongshuo Zhang, Dapeng Tan, Shicheng Xu, Tiancheng Hu, Huan Qi, Lin Li   +5 more
doaj   +1 more source

Encyclopedia of 2D β′‐In2Se3 Growth Using Chemical Vapor Deposition: The Effects of Synthesis Parameters Onto Material Quality

Advanced Engineering Materials, EarlyView.
A distinct semi‐confined inner‐tube chemical vapor deposition geometry enables reproducible, large‐area growth of phase‐pure 2D β′‐In2Se3 from InI + Se precursors. Engineering local vapor transport and optimizing precursor delivery and temperature–time conditions yield uniform continuous films.
Dasun P. W. Guruge, P. Sanju S. Panawala, Joseph F. S. Fernando, Zhenhuan Chen, Chao Zhang, Dong‐Chen Qi, Liangzhi Kou, Konstantin L. Firestein, Dmitri V. Golberg   +8 more
wiley   +1 more source