Results 11 to 20 of about 1,265 (179)
Adhesion and wear of diamond: formation of nanocracks and adhesive craters of torn out material [PDF]
Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences, 2022 Mechanical transformation of rough diamonds into brilliant ones is usually achieved by polishing using microsized abrasive diamond particles. It is shown that in addition to formation of periodic pattern of ‘partial’ Hertzian cone cracks on the diamond surface, nano-sized domains (50–150 nm in diameter) of crumbled material are observed.
Feodor M. Borodich +2 more
openaire +2 more sources
Methods of data analysis for the ball cratering test on TiN and DLC coated steel [PDF]
Materials Research, 2016 Titanium nitride (TiN) coatings are widely used in machining because of its mechanical characteristics which modify the surface of the substrate increasing the capacity of load support and reduction of friction, while a coating as diamond-like carbon ...
W. M. Silva, P. S. Souza, J. R. Carneiro
doaj +1 more source
Applied Surface Science Advances, 2021 The present study was aimed to analyze a slurry erosion failure of SS316L steel coated with high-velocity oxygen-fuel coatings using Ni–20Cr2O3, Ni–30Al2O3, and Al2O3–13TiO2.
Jashanpreet Singh
doaj +1 more source
Metals, 2019 In this work, the analysis of the cutting speed and feed rate influence on tool wear and cutting forces in Ti6Al4V alloy dry machining is presented. The study has been focused on the machining in a transient state.
Yezika Sánchez Hernández +3 more
doaj +1 more source
Wear Resistance of Coating Films on Hob Teeth
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2012 The wear resistance of coating films on hob teeth is investigated through the simulated hobbing tests with a flytool. The coating films on hob teeth are titanium family ceramics such as TiN, TiCN, TiSiN and TiAlN and aluminum chromium family ceramics ...
Yoji UMEZAKI +4 more
doaj +1 more source
Engineering Reports, 2020 This work deals with plane strain finite element modeling for orthogonal cutting process of carbon steel. The experimental work conducted on a center lathe machine using carbide tools.
Hatem A. Soliman +3 more
doaj +1 more source
Crater Wear Prediction of Coated Tools.
Journal of the Japan Society for Precision Engineering, 1993 No matter what wear mechanism controls tool wear, tool wear rate can be expressed as functions of stress and temperature on the tool face. Thus stress and temperature distributions on the rake face were measured with split tools and with thermocouples respectively to obtain wear equations.
OBIKAWA, Toshiyuki +4 more
openaire +2 more sources
A study on the crater wear of cermet tools. Wear mechanism at high speed cutting.
Journal of the Japan Society for Precision Engineering, 1986 The purpose of this study is to clarify the wear mechanism at high speed cutting, that is, high tool face temperature where mutual diffusion at interface comes to active. The relation is investigated and discussed between the crater wear rate and the condition of diffusion layer by cutting test and dynamic diffusion test, for reference.
Ei-ichi SENTOKU +2 more
openaire +3 more sources
Fundamental research on hobbing considering environment (Influence of various coating films)
Nihon Kikai Gakkai ronbunshu, 2015 This paper presents tool life (flank wear) and crater wear of four kinds of coated high-speed steel tools and finished surface roughness in hobbing under the conditions of considering environment.
Hironori MATSUOKA +7 more
doaj +1 more source
High Temperature Materials and Processes, 2011 Manufacturing process is significantly altered by tool wear and this factor creates intricate issues that form a hindrance in attaining manufacturing automation.
Maniraj Jaganathan +4 more
doaj +1 more source