Modeling of cardiac muscle thin films: Pre-stretch, passive and active behavior [PDF]
, 2014 Recent progress in tissue engineering has made it possible to build contractile bio-hybrid materials that undergo conformational changes by growing a layer of cardiac muscle on elastic polymeric membranes.
Bertoldi, Katia +4 more
core +1 more source
On the mechanics of chip formation in Ti-6Al-4V turning with spindle speed variation [PDF]
, 2014 "In order to enhance material removal rate (MRR), a strategy that relies on higher depths of cut could be chosen if vibrational issues due to regenerative chatter did not occur.
ALBERTELLI, PAOLO +4 more
core +1 more source
The Arctic Coastal Erosion Model: Overview, Developments, and Calibration at Drew Point, Alaska
Journal of Advances in Modeling Earth Systems, Volume 18, Issue 3, March 2026.Abstract Permafrost coastlines are experiencing significant erosion as polar amplification has enhanced the effects of climate change in the Arctic. Warmer temperatures are increasing thermo‐denudation and more energetic oceans are increasing thermo‐abrasion in unlithified, ice‐bonded permafrost coastlines which comprise at least 40% of the circum ...
Elyce Bayat +10 more
wiley +1 more source
Basin Research, Volume 38, Issue 2, March/April 2026.Basin‐scale correlation of Messinian salinity crisis (MSC) deposits across the Apennine–Albanide foreland basin system integrating outcrop and subsurface data. ABSTRACT We reconstructed the geological evolution of the Albanides during the Messinian salinity crisis (MSC), based on the integration of outcrop and subsurface data from both onshore (peri ...
Bigi Diego +4 more
wiley +1 more source
Electrical Transport in High Quality Graphene pnp Junctions
, 2009 We fabricate and investigate high quality graphene devices with contactless, suspended top gates, and demonstrate formation of graphene pnp junctions with tunable polarity and doping levels. The device resistance displays distinct oscillations in the npn
Chun Ning Lau +4 more
core +1 more source
Comparison of Flank Super Abrasive Machining vs. Flank Milling on Inconel® 718 Surfaces [PDF]
, 2018 Thermoresistant superalloys present many challenges in terms of machinability, which leads to finding new alternatives to conventional manufacturing processes.
Calleja Ochoa, Amaia +4 more
core +2 more sources
The comparison of dual wavelength fiber laser spectrum in SMF and HNLF by utilizing laser diode [PDF]
, 2016 A dual-wavelength erbium-doped fiber (EDF) fiber ring laser in single mode fiber and highly nonlinear fiber is demonstrated and both optical spectrums are compared at 400 mA of Laser Diode (LD) output. The fiber ring laser cavity incorporated sagnac loop
Awang, N. A. +3 more
core
Modelling and simulation of the dynamic cutting process and surface topography generation in nano/micro cutting [PDF]
, 2008 In nano/micro cutting process, the surface quality is heavily dependent on all the dynamic factors in machining including those from the material, tooling, cutting parameters, servo accuracy, mechanical structure deformation, and non-linear factors as ...
Cheng, K, Zhou, L
core
Prediction of grinding machinability when grind P20 tool steel using water based ZnO nano-coolant [PDF]
, 2012 Grinding is often an important finishing process for many engineering components and for some components is even a major production process. The surface roughness, Ra is also an important factor affecting many manufacturing departments.
Yogeswaran, Muthusamy
core +1 more source
FEM-based prediction of workpiece transient temperature distribution and deformations during milling [PDF]
, 2018 In high-speed dry milling of thin-walled parts, the cutter-workpiece temperature rises asymptotically with cutting speed, causing excessive cutter tooth wear and workpiece thermal expansion, which in turn reduces the cutter life and produces dimensional ...
Rai, Jitender, Xirouchakis, Paul
core