Results 101 to 110 of about 153,105 (301)
OVERLOAD CAPABILITY OF POWER CABLES IN ACTUAL POWER CONSUMPTION SYSTEMS
Results of overload capability calculations for 6-kV power cables are analyzed. The work is aimed at creating a computation system for the current rating of high-voltage cross-linked polyethylene power cables.
L.A. Szhebenyuk
doaj
A 39-year-old woman underwent bilateral total hip arthroplasty with conventional, ethylene oxide–sterilised liners when she was a subject in a radiostereometric analysis study. Within 2 years she had rapid polyethylene wear with aggressive, asymptomatic,
LJ O'Hara, B Nivbrant, S Röhrl
doaj +1 more source
A fluorine‐rich acrylate monomer (PFHEA) was solvent‐free applied to NCM90 and thermally decomposed under Ar to convert residual lithium into LiF and form a pre‐built LiF/fluorinated amorphous carbon (LiF/FC) interphase. The LiF/FC layer suppresses NiO rock‐salt reconstruction and microcrack propagation, lowers interfacial resistance, and improves Li ...
Pangyu Kim +6 more
wiley +1 more source
Double sequential necking in cross-linked polyethylene
The phenomenon of double sequential neck formation during hydraulic tests of cross-linked polyethylene has been studied. It is shown that the extension ratio, formed under conditions of double neck formation at the first and second stages, varies in the range from 2 to 7.
A. G. Dementieva +2 more
openaire +1 more source
Coagulative granular hydrogels are composed of packed thrombin‐functionalized microgels that catalyze the conversion of fibrinogen into a secondary fibrin network, filling the interstitial voids. This bio‐inspired approach stabilizes the biomaterial to match the robustness of bulk hydrogels without compromising injectability, mimicking the initial ...
Zhipeng Deng +16 more
wiley +1 more source
Does the addition of vitamin E to conventional UHMWPE improve the wear performance of hip acetabular cups? Micro-Raman characterization of differently processed polyethylene acetabular cups worn on a hip joint simulator [PDF]
In knee replacements, vitamin E-doped ultra-high molecular weight polyethylene (UHMWPE) shows a better wear behavior than standard UHMWPE. Therefore, different sets of polyethylene (PE) acetabular cups, i.e.
M. Di Foggia, S. Affatato, P. Taddei
doaj +2 more sources
The repair and regeneration of brain tissue faces both biological and technical challenges. Injectable bioscaffolds offer new opportunities to stimulate tissue regrowth in the brain by recruiting neural stem cells. Here, the translational issues are reviewed that need to be address to advance this promising new therapeutic approach from the bench to ...
Michel Modo, Alena Kisel
wiley +1 more source
Computational Modeling Meets 3D Bioprinting: Emerging Synergies in Cardiovascular Disease Modeling
Emerging advances in three‐dimensional bioprinting and computational modeling are reshaping cardiovascular (CV) research by enabling more realistic, patient‐specific tissue platforms. This review surveys cutting‐edge approaches that merge biomimetic CV constructs with computational simulations to overcome the limitations of traditional models, improve ...
Tanmay Mukherjee +7 more
wiley +1 more source
"Sub-Hertz" Dielectric Spectroscopy [PDF]
Dielectric spectroscopy measurements below 1 Hz are often dominated by “conduction-like” effects. For this reason, they often appear to be dismissed as being of little interest.
Ajour, M. N. +2 more
core
Aqueous Two‐Phase Bioinks for Discrete Packing and Compartmentalization of 3D Bioprinted Cells
Aqueous two‐phase systems (ATPS) enable the formation of biomimetic interfaces crucial for tissue engineering. However, clinical translation remains limited by the challenge of precisely controlling cellular compartmentalization. Here, we developed ATPS biomaterial inks for 3D bioprinting allowing tuneable droplet formation via NaCl modulation.
Martina Marcotulli +17 more
wiley +1 more source

