Results 21 to 30 of about 782,571 (165)
ABSTRACT Laser powder bed fusion (LPBF) of Inconel 718 alloy inevitably introduces pronounced microstructural anisotropy, typified by columnar grains and robust crystallographic texture. This results in direction‐dependent fatigue behavior, raising critical reliability concerns for high‐stakes aerospace applications.
Zhifang Shi +9 more
wiley +1 more source
ABSTRACT The intricate corrosion environment necessitates the polymeric coating's adaptability to the surroundings. In this work, the integration of rare‐earth Ce(III) ions and ethylene diamine tetramethylene phosphonic acid (EDTMP) in a layered double hydroxide (LDH) material is developed to enhance the corrosion protection and anti‐wear properties of
Yangu Liu +9 more
wiley +1 more source
ABSTRACT Objective To determine whether ultrasound is non‐inferior to positron‐emission tomography/computed tomography (PET/CT) and diffusion‐weighted magnetic resonance imaging (DW‐MRI) in terms of overall diagnostic accuracy for the preoperative assessment of pelvic lymph‐node status in cervical cancer.
F. Frühauf +14 more
wiley +1 more source
ABSTRACT Early diagnosis of liver cancer demands high sensitivity, high specificity, convenience and real‐time monitoring capabilities. However, it encounters challenges such as low concentration of markers, numerous interfering factors, and limitations of detection technologies.
Changsheng Shi +10 more
wiley +1 more source
ABSTRACT This study demonstrates a new strategy for modifying the boron content to address stress‐relief cracking (SRC) in the 7CrMoVTiB10.10 alloy. First, coarse‐grained heat‐affected zone (CGHAZ) specimens with different boron contents were prepared via simulated welding thermal cycles.
Dongdong Zhang +3 more
wiley +1 more source
目的研究结肠充气后CT扫描对结肠癌的诊断价值。方法随机选定本院门诊或住院的110例结肠癌患者,2012年2月至2018年2月对其进行结肠充气后进行CT扫描诊断,分析诊断结果,并与病理检测结果作比较。结果结肠充气后CT扫描:29例是浸润型癌、56例是肿块型癌、23例是溃疡型癌,诊断符合率为98.2%(108/110),漏诊2例,漏诊率为1.8%,结肠充气后CT扫描结果与病理检查结果比较,差异无统计学意义(P>0.05)。结论结肠癌患者采纳结肠充气后CT扫描诊断,诊断符合率较高,并且可以对病灶进行准确的分析,
王建明
core +1 more source
ABSTRACT Porous NiTi alloys are widely used in biomedical and engineering fields. Using the PBF‐LB technique, the TPMS and Voronoi porous parts with a porosity of ∼67% and a minimum feature size of 0.15 ± 0.02 mm were fabricated. Although the bulk sample fabricated with the same parameters is defect‐free, μ‐CT reconstruction on the porous sample ...
Wen‐Hao Zeng +7 more
wiley +1 more source
ABSTRACT Objective To test the non‐inferiority of extended abdominopelvic ultrasound examination compared with contrast‐enhanced computed tomography (CT) and whole‐body diffusion‐weighted magnetic resonance imaging (WB‐DWI/MRI) in discriminating preoperatively between resectable and non‐resectable disease based on the European Society for Medical ...
D. Fischerova +26 more
wiley +1 more source
Yttrium Addition Co‐Enhances the Plasticity and Corrosion Resistance of TiB2‐Refined Al‐Mg‐Zn Alloys
ABSTRACT To address the degradation of corrosion resistance induced by Al‐5Ti‐B grain refiner during the strengthening of Al‐Mg‐Zn alloys, this study innovatively employed a rare earth element yttrium (Y) alloying strategy to achieve synergistic enhancement of mechanical strength and corrosion resistance.
Wen‐Tao Qin +9 more
wiley +1 more source
ABSTRACT Objective To determine the diagnostic accuracy of virtual autopsy using whole‐body postmortem ultra‐high field magnetic resonance imaging (MRI) at 7 Tesla (T), using a short T2‐weighted imaging (T2‐WI) protocol, compared with classical autopsy, for detecting structural abnormalities in small second‐trimester fetuses. Methods Thirty consecutive
A. Staicu +11 more
wiley +1 more source

