Results 41 to 50 of about 14,859 (303)
Advanced Engineering Materials, EarlyView.This article presents a solver‐agnostic domain‐specific language (DSL) for computational structural mechanics that strengthens interoperability in virtual product development. Using a hierarchical data model, the DSL enables seamless exchange between diverse simulation tools and numerical methods.
Martin Rädel +3 more
wiley +1 more source
Motion of Small Bubbles near a Grid Spacer in a Two by Three Rod Bundle
Journal of Fluid Science and Technology, 2008 Motion of small bubbles upstream of a grid spacer in a two by three rod bundle is experimentally investigated. Trajectories of single bubbles upstream of the grid spacer are recorded by using a high-speed video camera. An image processing method based on
Zheng ZHANG +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This article provides an overview of recent advancements in bulk processing of rare‐earth‐free hard magnetic materials. It also addresses related simulation approaches at different scales. The research on rare‐earth‐free magnetic materials has increased significantly in recent years, driven by supply chain issues, environmental and social concerns, and
Daniel Scheiber, Andrea Bachmaier
wiley +1 more source
Modeling and simulation of curved fibers in dry spinning scenarios
Results in Applied Mathematics, 2019 Dry spinning is characterized by the simultaneous production of multiple thin polymeric fibers in airflows and the evaporation of the solvent contained in these fibers.
Manuel Wieland +3 more
doaj +1 more source
INFLUENCE OF THE ELASTO-PLASTIC BEHAVIOR OF TIE-RODS IN THE RESPONSE OF ROCKING MASONRY WALLS THROUGH SEISMIC DEMAND HAZARD CURVES [PDF]
, 2021 Fabio Solarino +2 more
openalex +1 more source
Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6
Advanced Engineering Materials, EarlyView.The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter +4 more
wiley +1 more source
Mechanically Deposited Wear‐Resistant Amorphous Zr55Cu30Al10Ni5 Coatings
Advanced Engineering Materials, EarlyView.Mechanically deposited from glassy ribbons, the Zr55Cu30Al10Ni5 amorphous coating formed a hard, continuous layer on AISI 1010 steel, tripling substrate hardness, lowering friction, and reducing wear. Despite its rough surface, it showed friction and wear behavior comparable to the crystalline alloy, highlighting its strong potential as a durable ...
Tales Ferreira +8 more
wiley +1 more source
International Journal of Smart and Nano Materials, 2022 A design strategy for a mechanical metamaterial with large negative hygroscopic expansion (NHE) was proposed in this paper. Different from the reported structures, the present metamaterial is designed by constructing repeated lattice microstructure ...
Lian-Hua Ma +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Calculation of Open Profile Thin-Walled Rod Systems Strengthened Under Load in Elastic and Plastic Deformations [PDF]
Учёные записки Казанского университета: Серия Физико-математические науки, 2015 This paper presents a variational method for calculation of open profile thin-walled rod systems strengthened under load. The main relations of the method are described.
M.N. Serazutdinov, M.N. Ubaydulloyev
doaj