Results 91 to 100 of about 804,929 (308)
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Influence of Cutting Depth on Rock Breaking Mechanism of PDC Cutter at Ultra-High Speed
Shiyou jixie, 2022 Ultra-high speed diamond drilling technology,which is characterized by high drilling efficiency with substantially lower low energy and load,is one of the effective means to improve ROP in deep and hard rock drilling.In order to understand the influence ...
Li Qizhou +5 more
doaj
Selection of Optimal Condition for Reducing Dimensional Error of Holes in Dry Cutting of Polyacetal Resin with Indexible Drill [PDF]
한국정밀공학회지In this study, polyacetal plates were machined with an indexable drill (Ø18mm) to measure the dimensional error of holes according to the cutting conditions and investigate the influencing factors to obtain precision holes.
Seho Chun
doaj +1 more source
Improvement of Machining Thin-Walled Parts Generated by Hybrid Manufacturing Using Optimalized Support [PDF]
, 2018 This paper is intended to show the problem in the production of thin-walled parts using hybrid manufacturing. It is necessary to machine the parts generated by 3D printing at certain stages of the production process.
Hosnedl S., Smolík J.
core
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Shiyou jixie, 2021 The deep and complex formations in oil and gas exploration and development have the characteristics of high pore pressure, high temperature, high rock hardness, strong plasticity and poor drillability, which have brought many challenges to drilling ...
He Zhenguo +5 more
doaj
Finite Element Analysis and Statistical Method to Determine Temperature Distribution on Cutting Tool in End-Milling [PDF]
, 2009 The aim of this study is to determine the temperature distribution on cutting tool when machining HASTELLOY C-22HS with carbide coated cutting tool.
K., Kadirgama +3 more
core
The Modus Vivendi of Persons with Schizophrenia: Valueception Impairment and Phenomenological Reduction [PDF]
, 2018 So far, the value dimension underlying affectivity disorders has remained out of focus in phenomenological psychopathology. As early as at the beginning of the 20th century, however, German phenomenologist Max Scheler examined in depth the relationship ...
Cusinato, Guido
core +1 more source
The Ratio of Feed to Depth of Cut in Metal Cutting
Journal of the Japan Society of Precision Engineering, 1962 When a metal is cut simultaniously by end and side cutting edges of a tool with the back rake angle i and side rake angle λ, the chip flows to a definite direction determined not only by the rake angles, but also by the ratio of feed to depth of cut.The optimum chip-flow direction of minimum energy can be controlled by choosing the ratio of feed to ...
openaire +2 more sources
Advanced Engineering Materials, EarlyView.High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin +4 more
wiley +1 more source