Results 11 to 20 of about 114,649 (262)
Micromachines, 2022 As research progresses, the surface texture tool can significantly reduce the cutting heat and cutting force. However, the tool surface texture width, depth, and spacing also have an impact on the cutting performance.
Shujing Wu, Dazhong Wang, Jiahui Yin
doaj +1 more source
Finite element modelling of rock mass cutting by cutters for PDC drill bits
Petroleum Exploration and Development, 2015 A finite element model of the process of polycrystalline diamond compact (PDC) drill bit cutters cutting rocks was built, and the rock linear and circular cutting processes for different shapes of PDC drill bit cutters were simulated.
T O Pryhorovska +2 more
doaj +1 more source
Machinability of Stone—Plastic Materials During Diamond Planing
Applied Sciences, 2019 This paper investigated the machinability of a stone–plastic composite (SPC) via orthogonal cutting with diamond cutters. The objective was to determine the effect of cutting depth on its machinability, including cutting forces, heat, chip ...
Zhaolong Zhu +4 more
doaj +1 more source
Инженерные технологии и системы, 2020 Introduction. The article deals with the problem of reducing the efforts when processing thin-walled bushings for hydraulic systems of agricultural machines with the ultrasonically activated cutting tool to achieve the specified processing accuracy and ...
Vladimir A. Skryabin
doaj +1 more source
Modeling of cutting of stainless steel AISI 304 by abrasive water jet
Materials Research Express, 2020 Abrasive water jet (AWJ) has distinct advantages in machining stainless steel, titanium alloy and other metals because of its high machining ability and cold working characteristics.
Xiaojin Miao, Meiping Wu
doaj +1 more source
Crystals, 2022 A three-dimensional cutting simulation prediction model based on DEFORM-3D finite element software was developed and experimentally validated, with a maximum error of 21.1% between the experimental and simulation results. The effects of the difference in
Xianjun Kong +4 more
doaj +1 more source
Doğu Kayını Ahşabının Yüzey Pürüzlülüğünün Bir Yapay Sinir Ağı ile Modellenmesi
Düzce Üniversitesi Bilim ve Teknoloji Dergisi, 2019 Bu çalışmanın amacı yapay sinir ağı(YSA) yaklaşımı ile doğu kayını (Fagusorientalis Lipsky) ahşabının yüzey pürüzlülüğünü modellemektir. İlk olarak,yatay bant zımpara makinesinin çalışma parametreleri (60-80-100 zımpara numarası,4-7-10 m/dk besleme hızı ...
Abdullah Cemil İlçe, Hilal Singer
doaj +1 more source
Simulation analysis on influencing factors of cutting head load of longitudinal roadheader
Gong-kuang zidonghua, 2020 In view of problem that single influencing factor can not fully reflect cutting head load and its fluctuation variation law in existing research methods of cutting head load characteristics for roadheader, by analyzing instantaneous load of cutting head,
FENG Junling +3 more
doaj +1 more source
On the depth of cutting planes
, 2019 We introduce a natural notion of depth that applies to individual cutting planes as well as entire families. This depth has nice properties that make it easy to work with theoretically, and we argue that it is a good proxy for the practical strength of cutting planes.
Poirrier, Laurent, Yu, James
openaire +2 more sources
The cutting behavior of cortical bone in different bone osten cutting angles and depths of cut [PDF]
, 2021 Abstract Cortical bones are semi-brittle and anisotropic, this brings the challenge to suppress vibration and avoid undesired fracture in precise cutting processes in surgeries. In this paper, we proposed a novel analytical model to represent cutting processes of cortical bones, and we used to evaluate cutting forces and fracture toughness, and
Yuanqiang Luo +5 more
openaire +1 more source