Results 101 to 110 of about 168,439 (303)
Metals, 2016 In this paper, machining aeronautical aluminum alloy AA2024-T351 in dry conditions was investigated. Cutting forces, chip segmentation, and built-up edge formation were analyzed. Machining tests revealed that the chip formation process depends on cutting
Badis Haddag +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A wood‐based magnetic and conductive material called Magwood (MW), capable of blocking almost 99.99% of electromagnetic waves (in the X‐band frequency range), is synthesized using a simple, solvent‐free process. MW is lightweight, resists water, and is flame‐retardant, making it a promising alternative for shielding electronics. The rapid proliferation
Akash Madhav Gondaliya +3 more
wiley +1 more source
Research into the geometry of the delimbing head of cutting knives
Research in Agricultural Engineering, 2013 Limbing with a wedge tool as a chipless operation is accompanied by a large deformation of wood in the cutting plane, i.e. at the spot of contact with the tool face as well as in the zone adjacent to this plane.
J. Mikleš
doaj +1 more source
Investigation of tool geometry effect and penetration strategies on cutting forces during thread milling [PDF]
, 2014 The application of thread milling is increasing in industry because of its inherent advantages over other thread cutting techniques. The objective of this study is to investigate the effect of milling cutter tool geometry on cutting forces during thread ...
BRENDLEN, Romain +3 more
core +3 more sources
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Analysis and Simulation of Different Manufacturing Processes for Bevel Gear Cutting
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2008 Today manufacturers of bevel gears are confronted with continuously growing demands on the cost effectiveness of the manufacturing process. To enhance the productivity of manufacturing processes, the processing time has to be reduced.
Christian BRECHER +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
FEA modeling of orthogonal cutting of steel: a review [PDF]
, 2012 Orthogonal cutting is probably the most studied machining operation for metals. Its simulation with the Finite Element Analysis (FEA) method is of paramount academic interest.
Borzan, Marian +3 more
core +1 more source
Cutting a Convex Polyhedron Out of a Sphere
, 2010 Given a convex polyhedron $P$ of $n$ vertices inside a sphere $Q$, we give an $O(n^3)$-time algorithm that cuts $P$ out of $Q$ by using guillotine cuts and has cutting cost $O((\log n)^2)$ times the optimal.Comment: 10 ...
Ahmed, Syed Ishtiaque +2 more
core +1 more source
Modeling the geometry of the endoplasmic reticulum network [PDF]
, 2016 Conference ProceedingFirst International Conference, AlCoB 2014, held in July 2014 in Tarragona, Spain.We have studied the network geometry of the endoplasmic reticulum by means of graph theoretical and integer programming models.
Euler, R +3 more
core +1 more source