Influence of the Built-up Edge on the Stress State in the Chip Formation Zone During Orthogonal Cutting of AISI1045 [PDF]
, 2010 In-situ strain measurements with high energy synchrotron radiation during orthogonal cutting of AISI1045 were carried out. Thereby it was possible to determine the stress state in the chip formation zone during the cutting process.
Uhlmann, Eckart +2 more
core +1 more source
Dynamic effects on cutting forces with highly positive versus highly negative cutting edge geometries [PDF]
International Journal on Interactive Design and Manufacturing (IJIDeM), 2018 Understanding the influence of the cutting edge geometry on the development of cutting forces during the milling process is of high importance in order to predict the mechanical loads on the cutting edge as well as the dynamic behavior on the milling tool.
A. Agic +3 more
openaire +4 more sources
Development of Thermomechanical Model for the Analysis of Effects of Friction and Cutting Speed on Temperature Distribution around AISI 316L During Orthogonal Machining [PDF]
, 2017 In metal cutting,severe deformation takes place in the vicinity of the cutting edge of the high strain-rate and an increase in temperature is observed. Deformation behaviour of the work material in the primary and secondary zones is highly sensitive to ...
Abiola , Abatan +3 more
core +1 more source
Numerical and analytical modeling of orthogonal cutting : The link between local variables and global contact characteristics [PDF]
, 2011 The response of the tool–chip interface is characterized in the orthogonal cutting process by numerical and analytical means and compared to experimental results. We study the link between local parameters (chip temperature, sliding friction coefficient,
CHERIGUENE, Rachid +2 more
core +5 more sources
COMPARATIVE ANALYSIS OF CBN CUTTING INSERTS WITH DIFFERENT EDGE GEOMETRIES
Cutting & Tools in Technological System, 2019 In this paper the experimental results of newly developed cutting inserts with special geometry and position for machining of hardened surfaces are summarized. The design of the tool holder and cutting insert allows the increase of the applied feed values in hard turning.
Kundrák, János +2 more
openaire +4 more sources
Diyala Journal of Engineering Sciences, 2009 This work summarizes the effect of edge round preparation for three types of ceramic cutting tool materials (Al2O3/ZrO2, Al2O3/ TiC, Si3N4/Y2O3) upon cutting forces and stress distribution on the cutting tool in orthogonal cutting as determined with ...
Suha K. Shehab
doaj +1 more source
Effect of Machining Conditions on Temperature and Vickers Microhardness of Chips during Planing
Metals, 2022 For the machining of long and narrow surfaces and when processing multiple pieces, planing technology is used, the productivity of which can be higher than that of milling, although it is relatively slow machining. The article aims to study the degree of
Peter Pavol Monka +5 more
doaj +1 more source
Cemented Carbide End-Mill Edge Preparation Using Dry-Electropolishing
Journal of Manufacturing and Materials ProcessingPrecision edge preparation techniques for cemented carbides enable optimization of the geometry of tools’ cutting edges. These techniques are frequently used in high-stress environments, resulting in substantial improvements in tools’ cutting performance.
Guiomar Riu-Perdrix +3 more
doaj +1 more source
The role of tool geometry in process damped milling [PDF]
, 2010 The complex interaction between machining structural systems and the cutting process results in machining instability, so called chatter. In some milling scenarios, process damping is a useful phenomenon that can be exploited to mitigate chatter and ...
A Ganguli +23 more
core +1 more source
Wood Crosscutting Process Analysis for Circular Saws
BioResources, 2016 This article deals with the influence of some cutting parameters (geometry of cutting edge, wood species, and circular saw type) and cutting conditions on the wood crosscutting process carried out with circular saws.
Jozef Krilek +2 more
doaj +1 more source