Results 151 to 160 of about 89,685 (265)

Investigation of ultra-precision planing process to fabricate high luminance retroreflector based on cutting force and tool vibration analysis. [PDF]

Sci Rep, 2022
Jeong JY, Han JS, Kang CM, Gwak EJ, Choi DS, Je TJ.   +5 more
europepmc   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Multi-Objective Optimization of Surface Roughness, Cutting Force, and Temperature in Ultrasonic-Vibration-Assisted Milling of Titanium Alloy. [PDF]

Micromachines (Basel)
Hu G, Lu Y, Zhou S, He X, Zhang F, Zhu P, Wang M, Tan T, Chen G.   +8 more
europepmc   +1 more source

Fabrication, Performance, Characterization and Experimental Calibration of Embedded Thin-Film Sensor for Tool Cutting Force Measurement. [PDF]

Micromachines (Basel), 2022
Cheng Y, Wu W, Liu L, Zhang Y, He Z, Song D.   +5 more
europepmc   +1 more source

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

Advanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi, Alexander Adamczyk, Nora Brachhold, Gert Schmidt, Jana Hubálková, R. Gumeniuk, Alexandros Charitos, Christos G. Aneziris   +7 more
wiley   +1 more source

Quality of Machined Surface and Cutting Force When Milling NiTi Alloys. [PDF]

Materials (Basel)
Kowalczyk M, Tomczyk K.
europepmc   +1 more source

Effect of Pre-Existing Micro-Defects on Cutting Force and Machined Surface Quality Involved in the Ball-End Milling Repairing of Flawed KDP Crystal Surfaces. [PDF]

Materials (Basel), 2022
Lei H, Cheng J, Yang D, Zhao L, Chen M, Wang J, Liu Q, Ding W, Chen G.   +8 more
europepmc   +1 more source

On‐Demand Activation of Thin Alginate Shell Encapsulated Volatile Liquid for Untethered Pneumatic Soft Actuation

Advanced Engineering Materials, EarlyView.
Phase‐changing liquids enable untethered pneumatic actuation in soft robotics but suffer from volatility and storage challenges. This work reports a simple method to encapsulate Novec 7000 within micron‐thin alginate shells via in situ injection and ionic crosslinking.
Rayan A. M. Basodan, Jack Keddie, Byoungyoul Park, Hyun‐Joong Chung   +3 more
wiley   +1 more source

Influence of the Cooling Method on Cutting Force and Recurrence Analysis in Polymer Composite Milling. [PDF]

Materials (Basel)
Ciecieląg K.
europepmc   +1 more source

Prediction of Cutting Force and Chip Formation from the True Stress-Strain Relation Using an Explicit FEM for Polymer Machining. [PDF]

Polymers (Basel), 2022
Yang B, Wang H, Fu K, Wang C.
europepmc   +1 more source