Results 221 to 230 of about 3,826,227 (356)

Deep Learning Tool Wear State Identification Method Based on Cutting Force Signal. [PDF]

Sensors (Basel)
Li S, Li M, Gao Y.
europepmc   +1 more source

Cutting Force Acting on Blunt Cutting Edge. 1st Report. A Basic Consideration on Cutting Force Occurrence.

TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C, 2000
Eiji KONDO, Norio KAWAGOISHI, Takashi MUKAIHARA, Rikio HIKIJI   +3 more
openaire   +2 more sources

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

A Cutting Force and Hole Geometry Study for Precision Deep-Hole Microdrilling of Magnesium. [PDF]

Micromachines (Basel)
Pizzi M, Costetti A, De Gaetano F, Ferroni M, Arleo F, Boschetti F, Annoni M.   +6 more
europepmc   +1 more source

INFLUENCE OF SELECTED CUTTING CONDITIONS ON CUTTING FORCES

Advances in Science and Technology Research Journal, 2017
Augustín Görög, Dana Stančeková, Mária Kapustová, Ingrid Görögová, Izabela Miturska   +4 more
openaire   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

A novel prediction method for peak cutting force of curved picks considering lithological tolerances. [PDF]

Sci Rep
Duan M, Shao L, Huang Y, Huang Q, Liu J, Zhang Z.   +5 more
europepmc   +1 more source

iMachining Cutting Force Measurement

, 2016
Jan Hnatik, Jan Kutlwaser, Josef Sklenicka   +2 more
openaire   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Multi-objective optimization for minimize cutting force and power consumption in corn stalk chopping processes. [PDF]

Heliyon
Kumar Reddy KP, Kumar SR, Nageswara Rao B.   +2 more
europepmc   +1 more source