Results 201 to 210 of about 54,574 (258)

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Study on D6AC Steel PCBN Hard Turning and Optimization. [PDF]

Materials (Basel)
Liu Y, Huang S, Li R, Cui Z, Zhang Y, Liu C.   +5 more
europepmc   +1 more source

Model‐Guided Design of Paper Membrane Architectures for Controlled Flow and Enhanced Diagnostic Sensitivity

Advanced Engineering Materials, EarlyView.
Geometrical modifications on nitrocellulose membranes can result in observable differences in signal intensity relative to a reference membrane (top and bottom left). Using two reference experiments, we have developed a theoretical model that can reproduce the experimentally observed flow changes and provide information on membrane parameters, e.g ...
Maria Dimaki, Lea Holritz, Winnie E. Svendsen   +2 more
wiley   +1 more source

Drilling Performance of Novel Lightweight Carbon Specialty Graphites with Different Grain Sizes. [PDF]

ACS Omega
Kayihan M, Yildiz M, Kuzu AT, Bakkal M.
europepmc   +1 more source

Investigating the Effect of Inclination Angle and the Influence of Scan Parameters on the Appearance and Thermal and Mechanical Properties of Filigree Tension Rods of LPBF‐Manufactured NiTi Shape‐Memory Alloys

Advanced Engineering Materials, EarlyView.
This article investigates the dependence of the properties on the manufacturing orientation in the form of the inclination angle to the build plate of LPBF‐fabricated NiTi rods with a diameter of 150–220 µm. Metallographic, chemical, thermal, and mechanical characterization show behavior under identical manufacturing conditions that ranges from ...
Sandra Herzig, Michael Werner, Christian Rotsch   +2 more
wiley   +1 more source

Atomic-Scale Mechanisms and Damage Suppression in Nanometric Cutting of Polycrystalline Copper: A Molecular Dynamics Study. [PDF]

Nanomaterials (Basel)
Li Y, Fu P, Gu H, Liang S, Li L, Jiang H, Hong Y, Li Z, Lu L, Tang R, Li Z, Li L.   +11 more
europepmc   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Investigation of Delamination and Cutting Force in the Drilling of AA7050-CFRP Hybrid Composite Stacks Used in Real Aerospace Applications. [PDF]

Polymers (Basel)
Taşcı F, Bayar A, Yüksel A, Yavaş Ç, Bolat Ç, Ercetin A, Akkoyun F, Yalçın B.   +7 more
europepmc   +1 more source

Effect of Cutting Conditions on Roughness and Cutting Force When Machining a Freeform Surface with Barrel Tools. [PDF]

Materials (Basel)
Reznicek M, Horava C, Zajicek J, Ovsik M.   +3 more
europepmc   +1 more source

Evaluating the performance of newly developed PVD-AlN-coated cermet tools in hard turning of AISI 4340 steel under dry and minimum quantity lubrication. [PDF]

Sci Rep
Jouini N, Yaqoob S, Ghani JA, Mehrez S.
europepmc   +1 more source