Technoeconomic and thermodynamic aspects of the edge cutting machining optimization
Advanced Engineering Research, 2016 The investigation objective is to develop a calculation method of selecting the optimum cutting speed corresponding to the minimum tool-wear rate. The analysis of the known optimization criteria such as tribological, thermal, energy and thermodynamic ...
Anatoliy A. Ryzhkin +3 more
doaj +1 more source
Investigation of Cutting Tools and Working Conditions Effects when Cutting Ti-6al-4V using Vegetable Oil-Based Cutting Fluids [PDF]
, 2015 Power consumed in metal cutting is typically converted into heat near the cutting tool edge. Cutting fluids are then provided to a cutting zone in order to improve the tribological characteristics of machining processes and to dissipate the generated ...
Gariani, Salah +4 more
core +1 more source
EFFICIENCY CRITERIA FOR LUBRICATING-COOLING FLUIDS
Вестник Северо-Кавказского федерального университета, 2022 There are currently many companies manufacturing a large number of lubricating fluids, which makes it hard for technologists (manufacturers) when trying to make their choice of a lubricating coolant.
Gennady I. Smagin +3 more
doaj
Experimental investigation of hydrodynamics of melt layer during laser cutting of steel [PDF]
, 2011 In laser cutting process, understanding of hydrodynamics of melt layer is significant, because it is an important factor which controls the final quality. In this work, we observed hydrodynamics of melt layer on kerf front in the case of laser cutting of
Remy Fabbro +3 more
core +1 more source
Study of the effect of cutting modes on output parameters under high-speed steel turn-milling
Advanced Engineering Research, 2022 Introduction. The article elucidates increasing the efficiency of turn-milling of powdered metal high-speed steel products. Turn-milling can be used as an alternative to the traditional turning method. The article describes advantages of the turn-milling
D. A. Matlygin +3 more
doaj +1 more source
Polarisation-mode coupling in (100)-cut Nd:YAG
Optics Express, 2006 We investigate the polarisation-mode dynamics and Lamb's mode coupling constant for orthogonally polarised laser states in a dual-mode (100)-cut Nd:YAG laser with feedback, and compare with an anisotropic rate equation model. The anisotropic (100)-cut Nd:YAG exhibits thermally-induced depolarisation and polarisation-mode coupling dependent on the pump ...
Aaron, McKay +2 more
openaire +2 more sources
Experimental study of the brittle–ductile transition in hot cutting of SG iron specimens [PDF]
, 2013 http://www.sciencedirect.com/science/article/pii/S0924013612002579The present paper investigates the brittle-ductile transition (BDT) of the primary shear zone during cutting of spheroidal graphite (SG) iron in the austenitization temperature range ...
EL MANSORI, Mohamed +2 more
core +1 more source
Cutting Forces Modeling in Finish Turning of Inconel 718 Alloy with Round Inserts [PDF]
, 2011 In turning, the applied forces have to be known as accurately as possible, especially in the case of difficult-to-cut materials for aircraft workpieces finishing operations.
Gérard Poulachon +7 more
core +1 more source
Machinability of cast irons at finishing face milling of flat surfaces by superhard materials
Технічна інженерія, 2021 The article presents the result of the analysis of machinability of cast irons with different physical and mechanical properties. The thermal processes that occur in the cutting zone and the influence of cutting modes and geometric parameters of the ...
S.I. , L.Ye. , P.P.
doaj +1 more source
Experimental study of the effect of rock blasting with various cutting forms for tunnel excavation using physical model tests [PDF]
Archives of Civil Engineering, 2021 Cutting blasting has been widely used for tunnel excavation. The cutting forms significantly influence the blasting effect. This research focuses on the study of the relationship between cutting forms and blasting effects.
Huaming An, Yushan Song, Deqiang Yang
doaj +1 more source