Effect of process parameters and optimization of CO2 laser cutting of ultra high performance polyethylene [PDF]
, 2010 The aim of this work is to relate the cutting edge quality parameters (responses) namely: upper kerf, lower kerf, ratio of the upper kerf to lower kerf and cut edge roughness to the process parameters considered in this research and to find out the ...
Olabi, Abdul-Ghani +2 more
core +2 more sources
Prediction the Effect of Cutting Parameters on Surface Roughness Using Taguchi Method [PDF]
Engineering and Technology Journal, 2013 In this study, the prediction of surface roughness of milled surfaces was carried out using Taguchi Method with four inputs, namely, cutting direction, stepover, feed per tooth and workpiece surface geometry.
Laith A. Mohammed, Ahmed A. Duroobi
doaj +1 more source
Investigating the CO2 laser cutting parameters of MDF wood composite material [PDF]
, 2011 Laser cutting of medium density fibreboard (MDF) is a complicated process and the selection of the process parameters combinations is essential to get the highest quality of the cut section.
Olabi, Abdul-Ghani +5 more
core +2 more sources
Initial Assessment of Abrasive Wear Resistance of Austempered Cast Iron with Vermicular Graphite
Archives of Metallurgy and Materials, 2014 The work compares the abrasive wear resistance of cast iron containing vermicular graphite, measured in the as-cast state and after austempering carried out at 290°C, 340°C, or 390°C.
Soiński M. S., Jakubus A.
doaj +1 more source
Influence of machining parameters on surface roughness in WEDM cutting [PDF]
Journal of Research and Innovation for Sustainable Society, 2020 Wire Electrical Discharge Machining is a cutting method used for obtaining parts with complex geometries or for cutting hard metals. This рарer ѕeekѕ to emрhаѕіze the іmрortаnce of thіѕ unconventіonаl technology аnd more ѕрecіfіcаlly the іmрortаnce of ...
Sergiu Lazăr
doaj +1 more source
Pre-evaluation on surface profile in turning process based on cutting parameters [PDF]
, 2009 Traditional online or in-process surface profile (quality) evaluation (prediction) needs to integrate cutting parameters and several in-process factors (vibration, machine dynamics, tool wear, etc) for high accuracy.
MA, Ning +3 more
core +1 more source
Modelling of cutting fibrous composite materials: current practice [PDF]
, 2015 Using fibre reinforced polymers (FRP) is increasing across many industries. Although FRP are laid-up in the near-net shape, several cutting operations are necessary to meet quality and dimensional requirements.
Kahwash, Fadi +5 more
core +1 more source
Metals, 2023 This paper investigated the influence of cutting parameters, including feed rate, cutting speed, tool nose radius, and wet or dry cutting conditions, on the resultant force, cutting edge/workpiece temperature, and surface roughness when turning grey cast
Magdy M. El Rayes +5 more
doaj +1 more source
Experimental Investigation of Surface Roughness Using Uncoated and Coated Tungsten Carbide Cutting Tool in Turning Operation [PDF]
Engineering and Technology Journal, 2021 The cutting process is an important process of industrialization. It is requisite to using advantage quality cutting tools in order to preserve the type of product.
Frzdaq Thamer, Ali Abbar, Farhad. Othman
doaj +1 more source
Influence of cutting parameters and plasma cutting mode on cutting quality and process noise [PDF]
Manufacturing Technology, 2020 Plasma cutting is an ever-evolving method of industrial cutting of materials. Like all modern methods, it must meet the requirements for the quality of the cut, but also the hygiene and safety regulations set by European legislation. New ways are being sought to reduce process noise while improving the quality of the cutting surface.
Marie Kolarikova +5 more
openaire +1 more source