Influence of Cutting Conditions on the Cutting Performance of TiAl6V4 [PDF]
Advanced Materials Research, 2011 The FEM simulation was developed to investigate the influences of cutting speed, uncut chip thickness and tool rake angle on the cutting performance of TiAl6V4. The FEM simulation was validated using experimental results and good agreement was obtained.
Gui Gen Ye +3 more
openaire +2 more sources
On the Cutting Performance of Segmented Diamond Blades when Dry-Cutting Concrete. [PDF]
Materials (Basel), 2018 The objective of the present study is to analyze and compare the cutting performance of segmented diamond blades when dry-cutting concrete. A cutting criteria is proposed to characterize the wear of the blades by measuring the variation of the external diameter and the weight loss of the blade.
Sánchez Egea AJ +5 more
europepmc +7 more sources
An investigation on micro cutting mechanics: Modelling, simulations and experimental case studies [PDF]
, 2014 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University London.Micro cutting is becoming increasingly important since miniature and micro components/products have become more and more demanded in precision ...
Sawangsri, Worapong
core +7 more sources
Improvement of Cutting Forces Modeling Based on Oriented Cutting Tests [PDF]
, 2013 In order to predict the characteristics of the machined part, such as geometry, surface roughness and fatigue or corrosion resistance, the cutting forces values should be known as precisely as possible.
Gérard Poulachon +10 more
core +1 more source
Alumina-based nanocomposite ceramic cutting tool materials toughened by graphene nanoplates
Cailiao gongcheng, 2019 Graphene nanoplates(GNPs), as toughening phase, toughened alumina-based nanocomposites ceramic cutting tool materials were fabricated by hot-pressing technology. The dispersing experiment of the GNPs was performed.
MENG Xiang-long +4 more
doaj +1 more source
Experimental study of the brittle–ductile transition in hot cutting of SG iron specimens [PDF]
, 2013 http://www.sciencedirect.com/science/article/pii/S0924013612002579The present paper investigates the brittle-ductile transition (BDT) of the primary shear zone during cutting of spheroidal graphite (SG) iron in the austenitization temperature range ...
EL MANSORI, Mohamed +2 more
core +1 more source
Levamisole: A High Performance Cutting Agent [PDF]
Academic Forensic Pathology, 2017 Levamisole is an imidazothiazole chemical most frequently used as an antihelminthic agent in cattle. Over the last decade, levamisole has been increasingly encountered as an additive in both powder and crack cocaine. A white powder with a “fish scale” appearance, the chemical is physically similar to powder cocaine.
Nadia, Solomon, Jonathan, Hayes
openaire +2 more sources
An Innovative Experimental Study of Corner Radius Effect on Cutting Forces [PDF]
, 2014 The cutting forces are often modelled using edge discretisation methodology. In finish turning, due to the smaller corner radii, the use of a local cutting force model identified from orthogonal cutting tests poses a significant challenge. In this paper,
BISSEY BRETON, Stéphanie +4 more
core +1 more source
Journal of Asian Ceramic Societies, 2023 To improve the cutting performance and prolong the service life of a carbide-coated tool in the process of ductile iron machining, an electromagnetic coupling treatment (EMCT) was carried out.
Kaien Sun +6 more
doaj +1 more source
Experimental Analysis and Geometrical Modeling of Cutting Conditions Effect in 5 Axis Milling with Ti6Al4V Alloy [PDF]
, 2012 The 5 axis continuous milling is an advanced technique for free-form surfaces manufacturing. In finishing, this technique uses ball-end or hemispherical milling cutter.
PRAT, David +3 more
core +1 more source