Results 1 to 10 of about 7,476,610 (346)
Review of Cutting Temperature Measurement Methods. [PDF]
Materials (Basel), 2023 During the cutting process, large quantities of emitted heat are concentrated on a small surface area of the interface between the workpiece and the cutting edge. The resultant very high temperature significantly affects the tool life. Knowledge of maximum temperatures to be expected on the cutting edges is important, as it allows the cutting ...
Cichosz P, Karolczak P, Waszczuk K.
europepmc +4 more sources
Measurement of Cutting Temperature in Interrupted Machining Using Optical Spectrometry [PDF]
Sensors, 2023 This research presents an experimental study focused on measuring temperature at the tool flank during the up-milling process at high cutting speed. The proposed system deals with emissivity compensation through a two-photodetector system and during ...
Isaí Espinoza-Torres +6 more
doaj +2 more sources
COATED TOOL CUTTING TEMPERATURE
Advanced Engineering Research, 2014 The analysis of the cutting area circuit diagram has shown that coatings on the edges of the hole and on the flank surface of the tool change the thermoelectric power measured by the dynamic thermocouple to the value of not more than 0.3-0.7%.
Anatoly Andreyevich Ryzhkin +3 more
doaj +3 more sources
Effect of Cutting Parameters on Cutting Temperature of TiAl6V4 Alloy [PDF]
Applied Mechanics and Materials, 2013 A Finite Element Modeling (FEM) and Simulation was Used to Investigate the Effect of Tool Rake Angle, Cutting Speed and Feed Rate on the Cutting Temperature of Tial6v4 Alloy. the Purpose of this Study was to Find Proper Cutting Parameters for Machining of Titanium Alloy where Cutting Temperature was Lowest. A FEM Based on ABAQUS Software which Involves
Sulaiman, Shamsuddin +2 more
openaire +4 more sources
Heat generation and histological analysis of peri-implant bone cutting using piezoelectric surgery for implant removal: an in vitro study [PDF]
International Journal of Implant DentistryPurpose This study aimed to evaluate the safety of piezoelectric surgery for bone cutting during implant removal in terms of heat generation and histological changes.
Yoshiki Saito +9 more
doaj +2 more sources
Research review on cutting temperature and cutting vibration of titanium alloy [PDF]
MATEC Web of Conferences, 2021 The text should be set to 1 line spacing. The abstract should be centred across the page, indented 17 mm from the left and right page margins and justified.
Li Yuqing, Li Shuncai, Yu Qiu
doaj +1 more source
Milling Force Modeling Methods for Slot Milling Cutters
Machines, 2023 The slot milling cutter is primarily used for machining the tongue and groove of the steam turbine rotor, which is a critical operation in the manufacturing process of the steam turbine rotor.
Mingzhou Wu +3 more
doaj +1 more source
PCD tool wear in cutting SiCp/6005Al composites
Jin'gangshi yu moliao moju gongcheng, 2023 To study the tool wear mechanism of turning SiCp/6005Al and the influence of tool wear on cutting force, cutting temperature and workpiece surface quality, cutting experiments at different speeds V and different feed speeds f were carried out.
Jieqiong LIN, Ru JIA, Yan ZHOU, Yan GU
doaj +1 more source
Metals, 2023 This paper investigated the influence of cutting parameters, including feed rate, cutting speed, tool nose radius, and wet or dry cutting conditions, on the resultant force, cutting edge/workpiece temperature, and surface roughness when turning grey cast
Magdy M. El Rayes +5 more
doaj +1 more source
The performance of modified jatropha-based nanofluid during turning process [PDF]
, 2021 The industry's extensive use of petroleum-based metalworking fluid (MWF) harms the environment and humans. The production of bio-based MWF, especially from crude jatropha oil (CJO), has therefore taken numerous initiatives.
Abdullah, H. +6 more
core +1 more source