Results 161 to 170 of about 7,476,610 (346)

Real‐World Performance of CSF Kappa Free Light Chains in the 2024 McDonald Criteria

Annals of Clinical and Translational Neurology, EarlyView.
ABSTRACT Objective Kappa free light chains (KFLCs) in the cerebrospinal fluid (CSF) have a similar performance to CSF‐restricted oligoclonal bands (OCB) for multiple sclerosis (MS) diagnosis. To help with implementation, we set out to resolve several remaining uncertainties: (1) performance in a real‐world cohort and the 2024 McDonald criteria; (2 ...
Maya M. Leibowitz, Ryan Cooper, Stefania Kaninia, Kathryn I. Challis, Will Greenway, Maria Bonello, Mahmoud Elbahnasawi, Deborah T. Shode, Dominika Gajdasik, Victor Iliev, Alison M. E. Whitelegg, Ian Galea   +11 more
wiley   +1 more source

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

Prediction of Cutting Temperature and Optimization of Process Parameters in Gear Skiving

Jixie chuandong
Gear skiving has been paid more and more attention for high efficiency and wide application in gear manufacturing. In gear skiving, prediction of cutting temperature and optimization of process parameters have an important influence on increasing tool ...
Wen Zijin, Chen Yongpeng
doaj  

Analysis of Cutting Tool Modification Effect toward Force, Power and Temperature at Cutting of Material St 42

Jurnal Energi Dan Manufaktur, 2012
Until now, research by using of a standard cutting tool at lathe process is still become a subject of many studies in order to reduce of the force, cutting power and temperature. However, there are no satisfactory results yet as expected.
I Gusti Komang Dwijana
doaj  

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Understanding the Effect of Resistance Temperature Detector Temperature Controllers on Microstructural Alignment in Magnetic Freeze Casting

Advanced Engineering Materials, EarlyView.
The effect of temperature controllers that are commonly used in freeze‐casting is investigated in this work. Temperature controllers are observed to generate a voltage in the slurry. Microstructural alignment and ultimate compressive strength data show this voltage to interfere with the ability to align the microstructure using magnetic fields ...
Maddie A. Schmitz, Steven E. Naleway
wiley   +1 more source

Composite Electrospun Fibers Containing Optimized B‐ and Cu‐Doped Bioactive Glass Sol‐Gel Particles for Potential Soft Tissue Engineering Applications

Advanced Engineering Materials, EarlyView.
This article describes the preparation and characterization of poly(ε‐caprolactone) electrospun composite fibers incorporating sol‐gel‐derived bioactive glass particles doped with B and Cu. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared spectroscopy, contact angle, acellular bioactivity, mechanical and ...
Elisa Piatti, Marta Miola, Liliana Liverani, Paolo Sartori, Enrica Verné, Aldo R. Boccaccini   +5 more
wiley   +1 more source

Adjustment of Coatings Morphology and Particle Distribution of Layered Silicates by Freeze‐Drying for Improved Gas Barriers

Advanced Engineering Materials, EarlyView.
Freeze‐drying of layered silicate is the key to get coatings with superior gas barrier. Freeze‐drying of layered silicates modified with dodecylamine (DDA) is a highly effective technique for the preparation of barrier pigments that significantly mitigate the permeation of oxygen, water vapor, and hydrogen through polymer films containing these ...
Joshua Lommes, Moritz Bätcher, Andrea Deißenberger, Volkmar Stenzel, Andreas Hartwig   +4 more
wiley   +1 more source

Is Young's Modulus a Critical Coating Property Determining Fouling‐Release Performance of Marine Coatings?

Advanced Engineering Materials, EarlyView.
The release of foulers from protective marine coatings is determined by several interrelated material properties, including the strength of Young's modulus, the flexibility of chain segments, the surface free energy, and the magnitude of hydrodynamic stress.
Johann C. Schaal, Andreas Brinkmann, Andreas Hartwig   +2 more
wiley   +1 more source

Enabling Digital Continuity in Virtual Manufacturing for Eco‐Efficiency Assessment of Lightweight Structures by Means of a Domain‐Specific Structural Mechanics Language: Requirements, Idea and Proof of Concept

Advanced Engineering Materials, EarlyView.
This article presents a solver‐agnostic domain‐specific language (DSL) for computational structural mechanics that strengthens interoperability in virtual product development. Using a hierarchical data model, the DSL enables seamless exchange between diverse simulation tools and numerical methods.
Martin Rädel, Andreas Schuster, Felix Schoenitz, Jean Lefèvre   +3 more
wiley   +1 more source