Results 231 to 240 of about 838,874 (359)

Influence of Temperature on Scratch and Wear Properties of Technical Thermoplastics: Implications for Material Selection

Advanced Engineering Materials, EarlyView.
The share of technical thermoplastics is expected to grow further in the e‐mobility segment. In this study, a detailed temperature‐based tribological characterization of technical thermoplastics is performed. The tribological properties are discussed in terms of the dynamic mechanical properties of polymers at different ambient temperatures. A proof of
Harsha Raghuram, Thomas Koch, Vasiliki-Maria Archodoulaki   +2 more
wiley   +1 more source

Effect of Yttrium and Rhenium Ion Implantation on the Performance of Nitride Ceramic Cutting Tools. [PDF]

Materials (Basel), 2020
Morozow D, Siemiątkowski Z, Gevorkyan E, Rucki M, Matijošius J, Kilikevičius A, Kilikevičius A, Caban J, Krzysiak Z.   +8 more
europepmc   +1 more source

On the Tool Wear in the Intermittent Cutting of the Reinforced Plastics : 3rd Report, Effect of the Cutting Fluid on the Tool Wear

, 1969
Yoshio Hasegawa, Shinsaku HANASAKI, Hidehiko Kita, Yoshiaki Kitamura   +3 more
openalex   +2 more sources

X‐Ray Computed Tomography Quantifies Primary Phases and Reveals Crack Morphology in High‐Cycle Fatigue of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
Primary phases and a fatigue crack are studied in a forged blank of an aluminum alloy using synchrotron and laboratory X‐ray computed tomography. To image the crack, the fatigue test is interrupted, and a static tensile load is applied to open the crack.
Jakob Schröder, Ying Han, Tobias Fritsch, Bardia Hejazi, Alexander Ulbricht, Birgit Skrotzki, Giovanni Bruno   +6 more
wiley   +1 more source

Machining Eco-Friendly Jute Fiber-Reinforced Epoxy Composites Using Specially Produced Cryo-Treated and Untreated Cutting Tools. [PDF]

Polymers (Basel)
Adin MŞ, Adin H.
europepmc   +1 more source

Some Considerations on Prevention of Chatter Vibration in Multi-Edge Rotary Cutting Tool (Continued)

, 1969
Shinobu KATO, Etsuo Marui
openalex   +2 more sources

Tribology of ZrC Coatings and Spherical Tips Acquired with Extraordinarily Stiff, Metal Atomic Force Microscopy Probes

Advanced Engineering Materials, EarlyView.
In this research, ZrC coatings are evaluated against various counterprobes at the microscale using novel super‐stiff atomic force microscopy cantilevers. The chemical composition of the coating is shown to be an important factor influencing coating hardness and Young's modulus, while surface roughness, counterprobe hardness, and surface energy are the ...
Piotr Jenczyk, Marcin Michałowski, Bogdan Warcholiński, Michał Milczarek, Adam Gilewicz   +4 more
wiley   +1 more source

The Influence of Contour Form Geometric Features and the Number of Cutting Passes on the Surface Quality Characteristics and Critical Points of Cutting Tools Fabricated by Wire Electrical Discharge Machining (WEDM). [PDF]

Micromachines (Basel)
Alinaghizadeh A, Azarhoushang B, Hadad M.   +2 more
europepmc   +1 more source

The Critical Raw Materials in Cutting Tools for Machining Applications: A Review. [PDF]

Materials (Basel), 2020
Rizzo A, Goel S, Grilli ML, Iglesias R, Jaworska L, Lapkovskis V, Novak P, Postolnyi BO, Valerini D.   +8 more
europepmc   +1 more source

Researches on Turning with Self-propelled Rotary Cutting Tool

, 1969
Susumu KASEI, Toshio HARA, Masahiro Masuda   +2 more
openalex   +2 more sources