Results 191 to 200 of about 323 (224)
Some of the next articles are maybe not open access.
Holzforschung
Abstract In this study, the feasibility of hydrophobizing pine wood veneers through gas grafting with palmitoyl chloride using a hot press was explored. To achieve this, the hydrophobization characteristics of wood veneer were analyzed under various conditions, including pressing temperature, time, and concentration of palmitoyl chloride.
Kyoung-Hwa Choi +2 more
exaly +2 more sources
Abstract In this study, the feasibility of hydrophobizing pine wood veneers through gas grafting with palmitoyl chloride using a hot press was explored. To achieve this, the hydrophobization characteristics of wood veneer were analyzed under various conditions, including pressing temperature, time, and concentration of palmitoyl chloride.
Kyoung-Hwa Choi +2 more
exaly +2 more sources
Cultural Veneer: Decorative Plastering in Utah’s Sanpete Valley
Utah Historical Quarterly, 1981Thomas Carter
exaly +2 more sources
Decorating wood flour/HDPE composites with wood veneers
Polymer Composites, 2016The low surface free energy makes wood plastic composites difficult to bond with traditional adhesives, such as urea formaldehyde resin (UF). This study investigates the decoration of wood flour/high‐density‐polyethylene composite (WF/HDPE) board with poplar wood veneers.
Li‐Min Guo +3 more
openaire +2 more sources
Manufacturing and Interfacial Bonding Behavior of EVA Film Reinforced Flexible Decorative Veneer
Wood and Fiber Science, 2021Polyethylene film reinforced flexible decorative veneer has attracted wide attention. However, its curling deformation has not been well solved due to the high processing temperature. Ethylene-vinyl acetate copolymer (EVA) has lower melting temperature and better flexibility than polyethylene.
Lu Fang +3 more
openaire +1 more source
A New In-Mould Decoration Process using Real Wood Veneer
Progress in Rubber, Plastics and Recycling Technology, 2006The use of real wood by manufacturers in automotive interiors is seen as a mark of a premium car quality. The current manufacture of aesthetic veneered components is both costly, resource demanding and time consuming. An alternative in-mould decoration manufacturing method is considered here, using back injection moulding of wood veneer onto plastic ...
K. Makenji +3 more
openaire +1 more source
Surface properties of different natural precious decorative veneers by plasma modification
European Journal of Wood and Wood Products, 2018Five kinds of typical natural precious decorative veneer rosewood, teak, black walnut, northeast China ash and red oak were treated by plasma at different discharge powers and speeds. The surface property changes of the treated and untreated wood were studied via contact angle, scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy ...
Xiaorui Peng, Zhankuan Zhang
openaire +1 more source
Holzforschung, 2018
AbstractA new type of plastic-film-reinforced pliable decorative sliced veneer (PF-RP-DSV) for wood product surface finishing was developed. The plastic film served as both the reinforcing and adhesive material. Consequently, the veneer did not need adhesives during preparation and wood surface finishing. However, the interface bonding strength between
Xiaorui Peng, Zhankuan Zhang
openaire +1 more source
AbstractA new type of plastic-film-reinforced pliable decorative sliced veneer (PF-RP-DSV) for wood product surface finishing was developed. The plastic film served as both the reinforcing and adhesive material. Consequently, the veneer did not need adhesives during preparation and wood surface finishing. However, the interface bonding strength between
Xiaorui Peng, Zhankuan Zhang
openaire +1 more source
Polymer Composites, 2022
Abstract Wood fiber reinforced thermoplastic composites are regarded as a kind of environmentally friendly material obtained by combining recycled thermoplastic and wood fibers together. However, they are difficult to be decorated for using due to their non‐polar, dense, and smooth surface characteristics.
Xuelian Zhou +5 more
openaire +1 more source
Abstract Wood fiber reinforced thermoplastic composites are regarded as a kind of environmentally friendly material obtained by combining recycled thermoplastic and wood fibers together. However, they are difficult to be decorated for using due to their non‐polar, dense, and smooth surface characteristics.
Xuelian Zhou +5 more
openaire +1 more source