Results 101 to 110 of about 184,696 (315)
Arthritis Care &Research, EarlyView.Objective This study aimed to investigate hand function trajectories over five years in primary hand osteoarthritis (OA). Additionally, determinants of baseline and longitudinal hand function were assessed. Methods A total of 538 patients with both baseline and five‐year study visits were analyzed.
Annemiek V. E. M. Olde Meule +4 more
wiley +1 more source
Deformation processes in polycrystalline aggregates of gypsum
, 1995 On the basis of both field and laboratory studies it is well established that polycrystalline gypsum is one of the weakest and most ductile rock materials found in the Earth's crust (e.g.
Meer, S. de +3 more
core
Integration of InSAR time series analysis and water vapour correction for mapping postseismic deformation after the 2003 Bam (Iran) Earthquake [PDF]
, 2009 Atmospheric water-vapor effects represent a major limitation of interferometric synthetic aperture radar (InSAR) techniques, including InSAR time-series (TS) approaches (e.g., persistent or permanent scatterers and small-baseline subset).
Fielding, E., Li, Z., Cross, P.
core +1 more source
Arthritis Care &Research, EarlyView.Systemic sclerosis (SSc) is a rare autoimmune disease defined by immune dysregulation, vasculopathy, and progressive fibrosis of the skin and internal organs. Despite advances in care, major complications such as interstitial lung disease (ILD) and myocardial involvement remain the leading causes of morbidity and mortality.
Cristiana Sieiro Santos +2 more
wiley +1 more source
NUMERICAL SIMULATION OF HYDRAULICALLY INDUCED CASING DEFORMATION IN SHALE RESERVOIR [PDF]
, 2018 Hydraulic fracturing stimulation is widely conducted to enhance hydrocarbon production in low-permeability reservoirs. However, the massive fracturing can lead to the well failure by compromising well integrity.
Xu, Ziyi
core
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Deformation and diagenetic histories around foreland thrust faults [PDF]
, 1990 This thesis is concerned with the relationship between deformation and fluid flow along thrust zones. The study was carried out in the Vercors, French Sub-Alpine Chains foreland thrust belt.
Roberts, Gerald Patrick
core
Materials Research Letters, 2019 Flash sintering has received wide attention lately due to its ultrafast densification process at low sintering temperature. However, the deformability of flash-sintered ceramics remains poorly understood. Yttria-stabilized zirconia (YSZ) was processed by
Jaehun Cho +8 more
doaj +1 more source
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source