Results 91 to 100 of about 81,051 (246)

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Elinvar Materials: Recent Progress and Challenges

Advanced Engineering Materials, EarlyView.
Elinvar materials, exhibiting temperature‐invariant elastic modulus, are critical for precision instruments and emerging technologies. This article reviews recent progress in the field, with a focus on the anomalous thermoelastic behavior observed in key material systems.
Wenjie Li, Yang Ren
wiley   +1 more source

Mutations of Laurent Polynomials and Flat Families with Toric Fibers

Symmetry, Integrability and Geometry: Methods and Applications, 2012
We give a general criterion for two toric varieties to appear as fibers in a flat family over P^1. We apply this to show that certain birational transformations mapping a Laurent polynomial to another Laurent polynomial correspond to deformations between
Nathan Owen Ilten
doaj   +1 more source

Advancing Research on Biomaterials and Biological Materials with Scanning Electron Microscopy under Environmental and Low Vacuum Conditions

Advanced Engineering Materials, EarlyView.
Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel, Lea Dierker, Antoine Eyram Kwame, Kim Nora Wagner, Jonas J. Unterholzner, Jan‐Henning Dirks, Dorothea Brüggemann   +6 more
wiley   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

PBF‐LB/M of Ti‐6Al‐4V: High‐Pressure Solution Treatment and Aging for Applications in a Sustainable Aerospace

Advanced Engineering Materials, EarlyView.
Additive manufacturing (AM) allows great geometric freedom for lightweight components. As parts are progressively optimized exploiting potentials in AM leading in smaller material cross sections, high pressure solution treating and aging (STA) treatments show an enormous potential for strongly improving material properties.
Mika León Altmann, Andre Danzig, Freerk Syassen, Rainer Fechte‐Heinen, Anastasiya Toenjes   +4 more
wiley   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

Advanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi, Ebrahim Norouzi, Kostiantyn Hubaiev, Jörg Waitelonis, Harald Sack   +4 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source