Results 31 to 40 of about 642,017 (309)
Virtual and augmented reality in dental education: The good, the bad and the better
European Journal of Dental Education, EarlyView., 2022 Abstract Introduction Virtual reality and augmented reality (VR/AR) are becoming established technologies with a wide range of possibilities in various academic fields, including dentistry. The practice of dentistry encompasses a spectrum of skills and knowledge of anatomy, complex technical and clinical skills and sound academic understanding.
Nikita Dzyuba +3 more
wiley +1 more source
Translucency of Dental Porcelains [PDF]
Journal of Dental Research, 1980 The translucency of comparable shades of five dental porcelains was determined. Both direct transmittance and total transmittance were measured at wavelengths of 400 - 700 nm. For 1 mm of porcelain, the values for direct transmittance were low and averaged 0.13 percent, whereas the values for total transmittance averaged 26.8 percent.
Brodbelt, R. H. W. +2 more
openaire +4 more sources
Odontology : official journal of The Society of the Nippon Dental University, 2023 This study aims at evaluating the effect of simulating porcelain firing on the microstructure, corrosion behavior and mechanical properties of a Co–Cr–Mo alloy fabricated by Metal Soft Milling (MSM).
A. Lekatou +5 more
semanticscholar +1 more source
Materials, 2022 This study was aimed at preparing zirconia samples via additive manufacturing (AM) and subtractive manufacturing (SM) and testing the following aspects: (1) the manufacturing accuracy of the zirconia samples and (2) the bond strength of porcelain to ...
Joon-mo Moon +7 more
semanticscholar +1 more source
Sintering of Dental Porcelain Enamels [PDF]
Journal of Dental Research, 1976 This study showed the effects of sintering temperature and atmospheric pressure on the density, tensile strength, and microstructure of porcelain enamels. Although the densities of the opaque porcelains were higher, they were weaker than the gingival porcelains.
Meyer, J. M., O'Brien, W. J., Yu, C. U.
openaire +4 more sources
Journal of Adhesion Science and Technology, 2021 The heat treatment of dental alloys prior to porcelain application/veneering has been proposed as a way to ensure sufficient oxide scale and to promote the porcelain’s adherence in porcelain-fused-to-metal (PFM) fixed dental prostheses. The present study
Maja Antanasova +4 more
semanticscholar +1 more source
Microorganisms, 2021 The aim of this paper was to study the effectiveness of a diode laser (LD) for removal of microorganisms isolated from porcelain and zirconia crown surfaces used in implantoprosthetics in order to minimize infections around dental implants.
Anna Wawrzyk +5 more
semanticscholar +1 more source
Knowledge protocol of direct and indirect Veneers among dental practitioners - A case study
Polytechnic Journal, 2023 Dental veneers are constructed from different materials such as porcelain, pressed ceramic, processed composite, or directly applied composite.The purpose of this study was to ascertain the preferred dental materials for veneers and the knowledge about ...
Sazan M. Azeez +3 more
doaj +1 more source
KEMAMPUAN LEKAT RESIN KOMPOSIT PADA REPARASI RESTORASI PORSELEN YANG FRAKTUR
Journal of Dentistry Indonesia, 2015 Since ceramic and metal ceramic restorations in crown and bridge have the potential to fracture, repairing porcelain restorations has become a serious cosmetic and clinical problem.
Ali Noerdin
doaj +1 more source
Porcelain Laminate Veneer Applications in Upper Anterior Region: Case report
Bezmiâlem Science, 2020 Recently, effects of rapidly developing technology have been seen in the dentistry. Advances in materials enable minimally invasive treatments in which dental tissue is preserved in order to provide esthetics.. Porcelain laminate veneer technique, one of
Zeynep Buket KAYNAR, Nazmiye DÖNMEZ
doaj +1 more source