Results 51 to 60 of about 1,487 (175)

Workflow to facilitate complete denture scanning with an intraoral scanner: A technique report

Journal of Prosthodontics, EarlyView.
Abstract Scanning a denture with an intraoral scanner is typically more challenging than scanning a dentate arch. This article describes a novel technique for digitally duplicating a complete denture. The workflow involves scanning an existing denture using an intraoral scanner with the addition of specific markers and subsequently constructing a ...
Jiayi Yu, Jiayi Lu, Berna Saglik, Junying Li   +3 more
wiley   +1 more source

Impact of monomer contamination of isopropanol during post‐rinsing on the accuracy of dental models fabricated by vat photopolymerization

Journal of Prosthodontics, EarlyView.
Abstract Purpose The aim of this study was to investigate the impact of an increasing level of monomer contamination of isopropanol (isopropyl alcohol [IPA]) during post‐rinsing on the dimensional stability of test samples produced by vat photopolymerization.
Florian Flierl, Benedikt C. Spies, Severin Rothlauf, Kirstin Vach, Ralf J. Kohal, Jörg Lüchtenborg   +5 more
wiley   +1 more source

A new insight into dental implant treatment for trauma-induced edentulism and associated temporomandibular joint disorders: A Case Report

Padjadjaran Journal of Dentistry
Introduction: Anterior implant placement is always challenging, especially when it is caused by trauma. Treatment preference is not only because of bone sufficiency but also aesthetic considerations.
Vita Mulya Passa Novianti, Seto Pramudita, Setiawan Bonifacius, Rasmi Rikmasari   +3 more
doaj   +1 more source

Influence of different manufacturing materials on the accuracy and fitting of full‐arch restorations using a photogrammetry scanner—In vitro study

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aimed to assess the accuracy of a photogrammetry scanner and evaluate the influence of four different manufacturing materials on the accuracy and fitting of full‐arch restorations made using a photogrammetry scanner. Materials and Methods A cast with six implant abutment analogs was made.
Paulo Sergio Borella, Abidiel Silva Guimaraes, Thais Silva Mendonça, Gus Khalil, Sandra Al‐Tarawneh, Lyndon F. Cooper, Gustavo Mendonça   +6 more
wiley   +1 more source

Regional odontodysplasia

Journal of Indian Society of Pedodontics and Preventive Dentistry, 2010
Regional odontodysplasia (ROD) is a rare developmental anomaly involving both mesodermal and ectodermal components in a group of contiguous teeth. It affects the primary and permanent dentitions in the maxilla and the mandible or both, however, the ...
Thimma Reddy B, Vinay Reddy K, Sunil B, Pujita R, Kiran K, Kranthi K   +5 more
doaj  

A Comparative Study of Microorganisms Adhered to Different Surfaces of Temporary Removable Partial Dentures

Journal of Nepalese Prosthodontic Society, 2018
Introduction: The purpose of this study was to identify and compare aerobic microorganisms adhering to polished and tissue surfaces of temporary removable partial dentures at 24hrs and at one week of dentures in use. Materials and methods: A total of 31 patients visiting the department of Prosthodontics for temporary removable partial dentures ...
P. Suwal, R.K. Singh, B.K. Chaudhari, B. Shrestha, Arati Sharma   +4 more
openaire   +2 more sources

Single‐Retainer Lithium Disilicate Resin‐Bonded Bridge for Mandibular Central Incisor Replacement Using CAD/CAM and Virtual Articulator: A 25‐Month Case Report

Clinical Case Reports, Volume 14, Issue 3, March 2026.
A digital workflow for lithium disilicate resin‐bonded prosthesis enables minimally invasive rehabilitation with improved accuracy and esthetics. ABSTRACT Rehabilitation of a missing mandibular central incisor with a resin‐bonded single‐retainer fixed dental prosthesis is challenging, particularly in young patients where implant placement may be ...
I. Hariri, F. Dabla, A. El Yamani
wiley   +1 more source

Resistência à flexão de resinas de metacrilato de metila e bisacrilato de metila submetidas à termociclagem

Revista de Odontologia da UNESP
OBJETIVO: Verificar a resistência à flexão de quatro resinas utilizadas para a confecção de restaurações temporárias submetidas à termociclagem. MÉTODO: Foram utilizadas as resinas da marcas Luxatemp e Structur 2, à base de bisacrilato de metila, e as ...
Ataís Bacchi, Luís Felipe Schneider, Fabiano Malafaia, Marcelo Garbossa   +3 more
doaj  

The First Case Report Of Regional Odontodysplasia With Auricular Malformation

International Dental Journal
Introduction: Regional odontodysplasia (RO) is a rare anomaly in tooth development and presents diagnostic and therapeutic challenges due to its unclear etiology.
Li Cheng, Lei Lei, Cai He, Zhou Yue, Li Yan, Qiu Bingrun   +5 more
doaj   +1 more source

Feasibility Study of a Behavioral Oral Health Intervention for People With Mental Health Challenges: A Self‐Regulation Approach

Health Science Reports, Volume 9, Issue 3, March 2026.
ABSTRACT Background and Aims People with mental health disorders experience disproportionately poor oral health and face persistent barriers to maintaining oral hygiene. This study aimed to assess the feasibility of supporting oral hygiene routines in community‐dwelling adults using a self‐regulation‐based education approach informed by Self ...
Grace Wong, Kyle Cheng, Mark Montebello, Carolyn Fraser, Zion Park, Anna Cheng, Marija Saponja, Lauren Monds, Wenpeng You   +8 more
wiley   +1 more source