Tendency of microbial adhesion to denture base resins: a systematic review [PDF]
Frontiers in Oral HealthObjectivesDigital denture fabrication became an alternative method to conventional denture fabrication. However reviewing the antimicrobial performance of newly introduced digital fabrication methods in comparison to the conventional method is neglected.
Firas K. Alqarawi, Mohammed M. Gad
doaj +2 more sources
Comparative evaluation of mechanical properties between dual-layer and bonded three-dimensional printed denture base materials: An in vitro study. [PDF]
J Indian Prosthodont SocChander NG +3 more
europepmc +2 more sources
Antifungal effects of eugenol on Candida albicans adherence to denture polymers [PDF]
PeerJ, 2023 Background The study’s objective is to assess the adherence of C. albicans in different types of denture polymers and the effectiveness of eugenol and commercialized denture cleansers in the removal of C. albicans.
Zubaidah Zanul Abidin +6 more
doaj +2 more sources
Measurements of surface scale changes in different denture base materials by stereophotogrammetric technique [PDF]
Journal of Dental Research, Dental Clinics, Dental Prospects, 2021 Background. This study aimed to evaluate the surface scale changes in the denture base material using different polymerization techniques, such as heat-cure/pressure polymerization system and injection molding technique with the stereophotogrammetric ...
Gonca Deste Gökay +3 more
doaj +1 more source
The Comparison of Retention between Hot Curing and Fluid Denture Base Acrylic Resin (In Vivo)
Al-Kitab Journal for Pure Sciences, 2022 Background and objectives: Adequate retention is a basic requirement for the acceptance of complete denture. The aim of this study was to evaluate the retention quality of fluid denture base materials and compare it with conventional acrylic denture ...
Bestun Luqman Akram +1 more
doaj +1 more source
Journal of Oral Biology and Craniofacial Research, 2022 Objective: The present study aimed to evaluate and compare the flexural strength and impact strength of heat-cured acrylic/Polymethyl methacrylate (PMMA) denture base resin and 3D printed denture base resin.
Mayank Chhabra +3 more
doaj +1 more source
Acrylic denture base repair (Part II): St-rength of acrylic denture base cured by four different techniques [PDF]
Al-Rafidain Dental Journal, 2006 Aim: To investigate the effect of repair techniques, surface treatment, and repair space design (3 mm space and no repair space) on the transverse, and tensile strengths of repaired denture base. Materials and methods: Four hundred and sixteen samples of
Repair acrylic denture base, microwave, thermo press. +1 more
doaj +1 more source
Shear Bond Strength of Acrylic Denture Teeth to PMMA and Polyamide Denture Base Materials [PDF]
Journal of Dental Materials and Techniques, 2018 Introduction: Detachment of denture teeth from denture base is one of the most common reasons for costly denture repairs .This study aimed at evaluating the bond strength of an acrylic denture tooth to polyamide injection-molded thermoplastic denture ...
Mohammadreza Nakhaei +3 more
doaj +1 more source
The Effect of Denture Base Surface Treatments on Microlekage of Soft Lining Materials [PDF]
Al-Rafidain Dental Journal, 2009 Aims: To evaluate the effect of two acrylic resin denture base surface trearments on microleakageof 4 soft denture lining materials (Tru–soft, Bony plus, UfiGel–P and Molloplast–B after 2 periods ofstorage and thermalcycling.
Munther N. Kazanji , Nadia T. Jaffer
doaj +1 more source
Evaluation of Antimicrobial Efficacy of Titanium Dioxide on Dental Plaque Colonisers: An In-vitro Study [PDF]
Journal of Clinical and Diagnostic Research, 2022 Introduction: Denture Stomatitis (DS), a common inflammatory condition of the denture bearing mucosa amongst denture wearers is strongly related to poor denture hygiene. Various materials have been incorporated into denture base acrylic resins to have an
Kapil Raju +2 more
doaj +1 more source