Results 21 to 30 of about 2,779 (229)
International Journal of Dentistry, 2022 Statement of Problem. The influence of various building angles on the tissue surface adaptation of complete denture bases fabricated using digital light processing is lacking. Purpose.
Kanyakorn Charoenphol +1 more
doaj +1 more source
Measurements of surface scale changes in different denture base materials by stereophotogrammetric technique [PDF]
Journal of Dental Research, Dental Clinics, Dental Prospects, 2021 Background. This study aimed to evaluate the surface scale changes in the denture base material using different polymerization techniques, such as heat-cure/pressure polymerization system and injection molding technique with the stereophotogrammetric ...
Gonca Deste Gökay +3 more
doaj +1 more source
Design of complete denture reinforced with metal base [PDF]
Stomatološki glasnik Srbije, 2013 Introduction. Complete denture reinforced with metal bases is fabricated in cases of fracture risk as well as in selected patients with neuromuscular disorders.
Poštić Srđan D.
doaj +1 more source
Dental Hypotheses, 2022 Introduction: We aimed to determine the maximum microwave disinfection cycles that is safe for the adaptability of polymethyl methacrylate (PMMA) denture bases under power–time setting of 630 W for 3 minutes.
Wan Nor Syariza Wan Ali +2 more
doaj +1 more source
Dental Research Journal, 2022 Background: Denture bases undergo repeated flexing during mastication leading to fatigue failure, demanding a high fatigue strength property. Flexural (transverse) strength is required high to prevent catastrophic failure under load for success.
Rutika C Patankar +5 more
doaj +1 more source
Evaluation of Tensile Bond Strength of Zinc Containing and Zinc Free Denture Adhesives on Different Denture Base Resin Materials: An in Vitro Study [PDF]
International Journal of Scientific Research in Dental and Medical Sciences, 2023 Background and aim: Denture adhesives augment the retention and stability of the complete denture. The included studies have not directly compared tensile bond strength between zinc and zinc-free denture adhesives.
Teena Wilson +5 more
doaj +1 more source
The Comparison of Retention between Hot Curing and Fluid Denture Base Acrylic Resin (In Vivo)
Al-Kitab Journal for Pure Sciences, 2022 Background and objectives: Adequate retention is a basic requirement for the acceptance of complete denture. The aim of this study was to evaluate the retention quality of fluid denture base materials and compare it with conventional acrylic denture ...
Bestun Luqman Akram +1 more
doaj +1 more source
Effectiveness of disinfectant solutions associated or not with brushing on the biofilm control of a 3D printed-denture base resin [PDF]
Journal of Applied Oral Science, 2023 The formation of biofilm on denture bases is a recurrent clinical problem that favors the development of denture stomatitis. The effectiveness of a hygiene protocol in a 3D-printed denture base resin is still uncertain.
Thaís Soares Bezerra Santos NUNES +4 more
doaj +1 more source
Effect of the processing cycle on dimensional changes of heat-polymerized denture base resins
Dental Research Journal, 2015 Background: The second processing cycle for adding the artificial teeth to heat-polymerized acrylic resin denture bases may result in dimensional changes of the denture bases.
Ghazal Savabi +3 more
doaj +1 more source
A new method for evaluating the retentive efficacy of different denture adhesives
Brazilian Journal of Oral Sciences, 2018 Aim: The aim of this study was to evaluate a new method for measuring the retention values of different denture adhesives. Methods: The adhesive strength values of three different commercial denture adhesives (Corega powder, Corega adhesive tape and ...
Simone Gomes Dias de Oliveira +7 more
doaj +1 more source