Results 11 to 20 of about 4,605,170 (283)
Managing design variety, process variety and engineering change: a case study of two capital good firms [PDF]
, 2012 Many capital good firms deliver products that are not strictly one-off, but instead share a certain degree of similarity with other deliveries. In the delivery of the product, they aim to balance stability and variety in their product design and ...
Alblas, A., Veldman, J.
core +5 more sources
An Estimation Method of the Manufacturing Process' Effect on Iron Losses
Advances in Electrical and Computer Engineering, 2014 More than 60% of industrial electricity consumption is made by electrical drives with induction motors. In 2008, by IEC 60034-30, the International Electrotechnical Commission defined the efficiency classes of induction motors namely: IE1, IE2 and IE3.
SCUTARU, G., GAVRILA, H., PETER, I.
doaj +1 more source
Sustainable design and the design curriculum [PDF]
, 2008 This paper reports on an initial study that begins the process of considering how design education should deal with the issue of sustainable design specifically in the context of the education of graduate designers in the fields of product, design ...
Humphries-Smith, Tania
core +1 more source
Design and analysis on the flow fluctuation of a new horizontal space multiphase crankshaft pump
The Journal of Engineering, 2018 In civil aviation ground deicing system, the traditional reciprocating pump is often used as the power supply device to ensure the physical and chemical properties of high viscosity deicing fluid.
Mengli Wu +6 more
doaj +1 more source
Design of a high water-based fluid, high-pressure, and large-flow safety valve
The Journal of Engineering, 2018 Aiming at solving the problem of low unloading sensitivity, bad dynamic performance and poor stability of high-pressure and large-flow relief valve in hydraulic support system, a new differential type of high-pressure and large-flow relief valve ...
Geqiang Li +3 more
doaj +1 more source
Designs, 2021 The design of an E segment, executive, midsize sedan car was chosen to fill a gap in the market of the Ford brand and to achieve the goal of innovation looking towards the future. Ford has not owned an E-segment flagship sports sedan for years, since the
Leonardo Frizziero +6 more
doaj +1 more source
Nano-textured polymers for future architectural needs
Journal of Facade Design and Engineering, 2013 Corresponding author: Prof. Dr. Dirk J. Broer, Professor at Eindhoven University of Technology, Chemical Engineering & Chemistry, Department of Functional Organic Materials & Devices (SFD), Helix building STO 0.34, Den Dolech 2, 5612 AZ Eindhoven, The ...
Cees W.M., Albert , Michael , Dirk J.
doaj +1 more source
Design rules to establish a credible More‐Electric Engine baseline power architecture concept
IET Electrical Systems in Transportation, 2023 The More‐Electric Engine (MEE), with its electrified engine auxiliary systems and increased multi‐shaft power offtake, is likely to become an increasingly central aspect of future More‐Electric Aircraft. Consequently, lightweight but resilient electrical
Qiyang Zhang +2 more
doaj +1 more source
Lightweight bonded acrylic facing at the Vitra VSL Factory
Journal of Facade Design and Engineering, 2013 Corresponding author: Matthias Michel, E-mail: michel@imagine-structure.eu Acrylic glass is omnipresent in the industrialised world; but as a building material most architects, facade planners and engineers are still unfamiliar with this material.
Matthias, Holger
doaj +1 more source
Comparison and development of sustainable office façade renovation solutions in the Netherlands
Journal of Facade Design and Engineering, 2013 Corresponding author: Ir. Michiel Ritzen, Eindhoven University of Technology/Zuyd University of Applied Sciences, The Netherlands. E-mail: m.j.ritzen@tue.nl Environmental, commercial and societal developments in the Netherlands stimulate the ...
Michiel, Bertold, Ronald , Zeger, Chris
doaj +1 more source