Results 51 to 60 of about 6,848,306 (172)
, 2009 SummaryThe collaboration between the Paul-Ehrlich-Institute (PEI) and the GTH as well as the two patient organisations, DHG and IGH has been official since February 2007 with the signing of the collaboration contract.
M. Heiden +4 more
core +1 more source
Thermal-hydraulic pre-test analysis of ICE test section with WA-DHR [PDF]
, 2011 This report, carried out at the DIMNP of the University of Pisa in collaboration with ENEA Brasirnone Research Centre, illustrates the thermal fluid-dynamics results of the WA-DHR pre-test analysis.
Martelli, D. +3 more
core +1 more source
Polymer Engineering &Science, EarlyView.Numerical simulation of polyethylene rotational molding using the Smoothed Particle Hydrodynamics (SPH) method. ABSTRACT This work presents the development of a numerical model based on the smoothed particle hydrodynamics (SPH) method to simulate the rotational molding process of powder thermoplastic polymers, used in the manufacture of liners for high‐
Ali Nourreddine +4 more
wiley +1 more source
Exploring the Physical Therapy Field at DHR
, 2023 1 Broadside. 48"W x 36"HI was able to shadow DPT Jesus Martinez from DHR Health Orthopedic and Sports Therapy Institute in Edinburg, Texas. I was not hands-on due to the institute of DHR’s protocols, but my shadowing experience consisted of ...
Valdes, Alexis Damian
core +1 more source
Polymer Engineering &Science, EarlyView.This illustration shows polyamide 6 (PA6) blended with 20–50% polybutylene succinate (PBS) by volume. The balance between tensile properties, fracture toughness and self‐healing capability is achieved in the 30% vol PBS blend. Thermal healing at 140°C results in 40% fracture toughness recovery in a blend containing 30% vol PBS.
Laura Simonini +5 more
wiley +1 more source
Leucaena Oil Functionalized With Osmium Tetroxide as a Precursor for Polyol‐Based Polyurethane
Journal of Polymer Science, EarlyView.Leucaena leucocephala seed oil is converted into a hydroxyl‐functional biopolyol through OsO4‐mediated dihydroxylation. The resulting biopolyol shows a hydroxyl number of 160–175 mg KOH g−1 and is successfully used to produce flexible, open‐cell polyurethane foams, highlighting a renewable route for converting underutilized biomass into value‐added ...
Giovanni Miraveti Carriello +13 more
wiley +1 more source
DHR leads to mitochondrial membrane potential collapse in human plasma cells.
, 2013 LP1 cells were treated with DMSO, 10 or 20 µM of DHR for 24 h, stained by TMRM alone (A) or in combination with Annexin V-FITC (B) followed by flow cytometric analysis.
Biyin Cao (437970) +7 more
core +1 more source
Secure interface architecture for the software defined system on wafer
Tongxin xuebaoTo address the lack of dynamic and heterologous characteristics for interconnect interface in software defined system on wafer, a dynamic heterologous redundancy secure interface (DHR-SI) architecture was proposed to maximize the reuse of functional ...
LI Peijie +4 more
doaj
Small, EarlyView.This study presents a robust strategy for 3D printing conductive, mechanically resilient MXene–CNF composite structures using a single‐step freeze‐induced crosslinking method. The printed architectures remain stable in both wet and dry states, exhibit high electrical conductivity and mechanical strength, and demonstrate practical application in fully ...
Nuzhet Inci Kilic +5 more
wiley +1 more source
Vine Tendril‐Inspired Cold‐Programmable Shape‐Memory Polymer Composites Using Sugar Beet Pulp
Small, EarlyView.Vine tendrils inspire a bio‐derived, cold‐programmable shape‐memory polymer composite (SMPC). Magnetically guided sugar beet pulp creates mesoscale heterogeneity within a glassy matrix, producing built‐in mechanical asymmetry for rapid, solvent‐free programming by simple stretching.
Wei Huang +9 more
wiley +1 more source