Results 91 to 100 of about 82,055 (340)
Unraveling the Cationic and Anionic Redox Reactions in a Conventional Layered Oxide Cathode [PDF]
, 2019 Increasing interest in high-energy lithium-ion batteries has triggered the demand to clarify the reaction mechanism in battery cathodes during high-potential operation.
Li, N +6 more
core +1 more source
DNA sensing by electrocatalysis with hemoglobin [PDF]
, 2012 Electrocatalysis offers a means of electrochemical signal amplification, yet in DNA-based sensors, electrocatalysis has required high-density DNA films and strict assembly and passivation conditions.
Barton, Jacqueline K. +2 more
core +2 more sources
Advanced Engineering Materials, EarlyView.A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain +7 more
wiley +1 more source
Study on the Direct Electrochemical Reduction of Fe2O3 in NaCl-CaCl2 Melt
International Journal of Electrochemical Science, 2019 The electrochemical reduction kinetics of Fe2O3 in melts were investigated by cyclic voltammetry, square wave voltammetry, open circuit potential and i-t curve analyses at 800°C utilizing a Fe2O3 cathode filled in a metal pore molybdenum strip and a ...
Hui Li +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Low‐consumable nickel ferrite‐based anodes for the Hall–Héroult process are compared with conventional prebaked carbon anodes using thermodynamic simulation and prospective life cycle assessment under contrasting future electricity system pathways from 2025 to 2050.
Felipe Alejandro Garcia Paz +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Cladding is a proven method that boosts the surface qualities of mechanical parts by applying a layer of more durable material over a base substrate. This work responds to the needs of offshore and pressure vessels sectors by focusing on cladding a super austenitic steel onto low‐carbon steel through gas tungsten arc welding.
E. J. da Cruz Junior +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser +4 more
wiley +1 more source
Microstructure Design of Steel‐Spinel Composites via Spark Plasma Sintering Process
Advanced Engineering Materials, EarlyView.This study illustrates how spark plasma sintering at reduced oxygen partial pressure enables controlled formation of steel‐spinel composites through tailored redox reactions and cation exchange. Comparison of the MgO–Fe2O3, steel–(MgO+Cr2O3), and steel–(MgO+Fe2O3) systems shows how oxygen activity and interface chemistry govern spinel formation, phase ...
Mahnaz Mehdizadehlima +4 more
wiley +1 more source
Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment
Advanced Engineering Materials, EarlyView.This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Viktoriia Shtefan, Thorgund Nemec, Ute Hempel, Annett Gebert and coworkers demonstrate that anodic treatment of Ti–Cu‐based metallic glass in a nontoxic pyrophosphate electrolyte forms a protective bilayered Ti/Zr‐oxide film enriched with Cu nanocrystals.
Viktoriia Shtefan +8 more
wiley +1 more source