Results 101 to 110 of about 3,162,083 (256)
Kinetics and Electrochemical Studies of Fe-substituted LiMnPO4
International Journal of Electrochemical Science, 2012 A simple sol-gel method was applied to synthesize LiMn(1-x)FexPO4 (x=0-0.5). The kinetics of LiMn(1-x)FexPO4 was studied by chemical delithiation experiment and EIS measurements. The results showed that the LiMn0.6Fe0.4PO4 has the fastest conversion rate
Jiali Liu +3 more
doaj +1 more source
Simulation of a transformer winding for partial discharge propagation studies [PDF]
, 2002 A simulation model of a continuous disc type 6.6 kV transformer winding was used to study the propagation behaviour of partial discharge (PD) pulses. The model based on multi-conductor transmission line theory uses a single turn as a circuit element with
Darwin, A. +4 more
core
Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials
Advanced Engineering Materials, EarlyView.Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley +1 more source
International Journal of Electrochemical Science, 2011 Amorphous Mg-based hydrogen-storage alloy (Mg70.6Ni29.4)90Nd10 is prepared by melt-spinning. The phase structures of the ribbons before and after charge/discharge cycling are characterized by high-resolution transmission electron microscopy (HRTEM), X ...
Huang Lin-jun +5 more
doaj +1 more source
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source
Remote controlled partial discharge acquisition unit [PDF]
, 2003 Online partial discharge (PD) analysis for underground high voltage cables has major advantages over the offline techniques. Online techniques usually involve PD data acquisition, storage and post-processing of the data.
Pearson, J.S. +3 more
core +2 more sources
Developing the Discharge Capacity of Al Husa'chi River
Engineering and Technology Journal, 2009 Al Husa'chi River is one of the three main branches of Al Ka’hla River in Maissangovernorate. Its length is 25 km. the river directly feeds Al Huwayza Marsh by overpasspipes at its end. It is also used for irrigating the nearby agricultural areas. A study forevaluating the hydraulic performance of the river has been carried out in order to developits ...
Muhannad J. Al- Kazwini +2 more
openaire +2 more sources
Fabrication Routes for Ionic Conducting Fiber Strain Sensors
Advanced Engineering Materials, EarlyView.Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw +3 more
wiley +1 more source
Shuili Shuiyun Gongcheng Xuebao, 2019 The interaction of flow occurs between the floodplain and the main river channel after the flood in the composite river channel overflows, which will form momentum exchange at the junction of the river channel and the floodplain.
YANG Po +3 more
doaj +1 more source
Fiduciary Capacity and the Bankruptcy Discharge [PDF]
, 2016 Bankruptcy law has fiercely competing policies. A primary one is the debtor\u27s fresh start. Another is that discharge of debt is a selectively conferred privilege rather than an unlimited right.
Byington, Jonathon S.
core