Results 201 to 210 of about 264,568 (355)

Discharge Coefficient Characterization of Jet Array Impingement Holes For An Active Clearance Control System [PDF]

, 2011
Riccardo Da Soghe, Bruno Facchini, Francesco Maiuolo, Mirko Micio, Livio Tarchi   +4 more
openalex   +1 more source

Evaluating Causal Links Between Chlorophyll <i>a</i> and Environmental Data in the Illinois River (USA). [PDF]

Ecol Evol
Larson JH, Bartsch LA, Jankowski KJ, Murphy JC, Kreiling RM.   +4 more
europepmc   +1 more source

Cap‐oPMN: Oral Inflammatory Load Quantification Using Capillary Microfluidics and Automated Image Processing

Advanced Materials Technologies, EarlyView.
ABSTRACT Quantifying oral polymorphonuclear neutrophils (oPMNs) is a clinically validated approach for assessing periodontal inflammation. However, current methods, such as manual hemocytometry and flow cytometry, are time‐consuming (>3 h), require invasive sampling, and depend on staining and complex instrumentation, making them unsuitable for point ...
Mohsen Hassani, Azam Zare, Fatemeh Soheili, S. M. Mahdi H. Daneshvar, Mahdi Amrollahi Biouki, Yasaman Tahernezhad, Chunxiang Sun, Michael Glogauer, Ebrahim Ghafar‐Zadeh, Amir Sanati‐Nezhad   +9 more
wiley   +1 more source

Experimental study to estimate the discharge coefficient over inclined side spillway

, 2020
Ayat Mehdi kadhim, Faisal A. Majid
openalex   +2 more sources

Discharge Coefficient of the Bar Screen

Journal of Rainwater Catchment Systems, 2000
Xingqi Zhang, Yasuhiro Akiyoshi, Takashi Watanabe, Satoshi Kai   +3 more
openaire   +2 more sources

The effect of patient experience with nurses and ward type on intention to recommend: Focusing on integrated nursing and caring service wards and general wards, 2020-2022. [PDF]

PLoS One
Kim J, Kim S.
europepmc   +1 more source

Additive Manufacturing of Ni‐Based Thermoelectric Materials for Waste Heat Recovery

Advanced Materials Technologies, EarlyView.
Thermoelectric generators convert waste heat into electricity but are constrained by conventional fabrication. Here, laser powder bed fusion enables direct printing of customised n‐type Cu60Ni40 and p‐type Ni90Cr10 legs. The assembled module achieves 0.8% efficiency at ΔT = 419 K, demonstrating scalable additive manufacturing of eco‐friendly, design ...
Karolin Amstein, Aayush Dobhal, Heiko Reith, Ran He, Julia Kristin Hufenbach, Kornelius Nielsch, Pingjun Ying   +6 more
wiley   +1 more source

Simulation of Discharge Coefficient of Sharp-Crested Circular Weirs Using Hybrid ANFIS-Firefly Model

, 2020
A. Alizadeh, Behrouz Yaghoubi, Saeid Shabanlou   +2 more
openalex   +1 more source

Stability and parameter sensitivity analysis of hydropower units under full operating conditions based on Pelton turbine refined models. [PDF]

Sci Rep
Xu R, Li C, Tan X, Wang H, Zhu Z.
europepmc   +1 more source

Graphene‐Based Wearable Textile Triboelectric Nanogenerators and Biomechanical Sensors

Advanced Materials Technologies, EarlyView.
This study presents a wearable textile‐based triboelectric nanogenerator (T‐TENG) using sprayed graphene enhanced with a PVA adhesion layer. The graphene‐based electrode demonstrates high electrical conductivity and robustness to multiple bends. The fabricated T‐TENG provides stable and efficient output, with strong responsiveness to biomotion.
Hongyang Dang, Benji Fenech‐Salerno, Antonio Alessio Leonardi, Federico La Barbera, Felice Torrisi   +4 more
wiley   +1 more source