Results 61 to 70 of about 60,973 (263)

Hydraulic characteristics of flow through rectangular vertical openings

Journal of Applied Science and Engineering
In this study an experimental work was conducted to characterize the hydraulic properties of flow through a wall containing rectangular vertical openings under both partially and fully submerged conditions.
Karim R. Gubashi, Saad Mulahasan, Haider Ali Al-Mussawy   +2 more
doaj   +1 more source

Derivation and verification of a new generalized formula set for calculating maximum instantaneous dam breach discharge

Shui kexue jinzhan, 2012
In order to calculate the maximum instantaneous dam-break discharge,a relationship between the maximum instantaneous dam-break discharge and the weir flow is established.The theory of equality of wave discharge and weir flow is applied in the study.A new
FANG Chong-hui, FANG Kun
doaj   +1 more source

Reliability and validity of the Readiness for Hospital Discharge Scale in patients with spinal cord injury

South African Journal of Physiotherapy, 2020
Background: Measuring rehabilitation outcomes in patients with spinal cord injury (PWSCI) requires measurement tools that are valid and reliable and have been psychometrically tested in the population with spinal cord injury (SCI).
Jacques S. De Lange, Jolandi Jacobs, Nadine Meiring, Boitumelo Moroane, Tinei Verster, Steve Olorunju, Mokgadi K. Mashola   +6 more
doaj   +1 more source

Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)

Advanced Engineering Materials, EarlyView.
Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho, M. Naeem, T. H. C. Costa, M. S. Libório, J. C. A. Queiroz, C. B. B. Luna, R. R. M. Sousa, P. S. Vieira, E. M. Araújo   +8 more
wiley   +1 more source

Influence of Surface Finish on the Tribological Performance of AlTiBN Coatings Deposited on Forming Tools

Advanced Engineering Materials, EarlyView.
Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver, Iker Alfonso, Eneko Barba, Javier León, José Antonio García, Iñaki Zalakain, Iván Fernández Martínez, Arley García‐Carrero, Christian Almeyda, Daniel Salcedo   +9 more
wiley   +1 more source

Discharge Coefficient Measurements for Flow Through Compound-Angle Conical Holes with Cross-Flow

International Journal of Rotating Machinery, 2004
Diffusion-shaped film holes with compound angles are currently being investigated for high temperature gas turbine airfoil film cooling. An accurate prediction of the coolant blowing rate through these film holes is essential in determining the film ...
M. E. Taslim, S. Ugarte
doaj   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

Advanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran, Vincent Nebel, Dominik Perius, Kshitij Kumar, Yannis Heim, Laura Bies, Tobias Kraus   +6 more
wiley   +1 more source

Development of readiness for discharge assessment scale of stroke patients

Huli yanjiu, 2020
ObjectiveTo develop the readiness for discharge assessment scale of stroke patients,and to provide a tool for evaluating discharge readiness of stroke patients.MethodsThe initial scale was formed through literature review and semi-structured interview ...
LIU Chenxing, ZHANG Wenguang, LI Yao, LI Xiaoyu   +3 more
doaj  

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source