Results 111 to 120 of about 152,792 (262)
Advanced Engineering Materials, EarlyView.This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca +9 more
wiley +1 more source
From Shear to Sound: Mechanics–Acoustics Mapping of TPMS Lattices
Advanced Engineering Materials, EarlyView.Triply periodic minimal surface (TPMS) lattices are mapped across mechanical and acoustic performance, revealing that descriptors validated in compression fail under shear. First‐time comparison with trusses included. A transition from porous to resonance‐driven absorption emerges at 25% density.
Lucía Doyle +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim +3 more
wiley +1 more source
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
Advanced Engineering Materials, EarlyView.Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley +1 more source
Advanced Functional Materials, EarlyView.Multiscale experiments and modeling reveal how Ti3C2Tx MXene nanosheets reinforce PVDF nanocomposites. An optimal MXene loading (∼1 wt.%) nearly doubles tensile strength through efficient stress transfer, flake alignment, and crack‐deflection mechanisms, transforming ductile polymer behavior into a controlled multi‐stage fracture pathway which aligns ...
Bita Soltan Mohammadlou +5 more
wiley +1 more source
Patient Preference and Adherence, 2013 Mickael Hiligsmann,1-3 Caroline van Durme,2 Piet Geusens,2 Benedict GC Dellaert,4 Carmen D Dirksen,3 Trudy van der Weijden,5 Jean-Yves Reginster,6 Annelies Boonen21Department of Health Services Research, School for Public Health and Primary Care (CAPHRI),
Hiligsmann M +7 more
doaj
Advanced Functional Materials, EarlyView.This study demonstrates that memristors can replace conventional 2T–1C driving circuits with simplified 1T–1 m architectures by exploiting resistance switching. With ultra‐low switching voltages (< ±0.2 V) and multi‐level resistance states, the memristors precisely control the current injected into organic light‐emitting diodes (OLEDs).
Dong Hyun Kim +6 more
wiley +1 more source