Results 141 to 150 of about 117,272 (312)

From Shear to Sound: Mechanics–Acoustics Mapping of TPMS Lattices

Advanced Engineering Materials, EarlyView.
Triply periodic minimal surface (TPMS) lattices are mapped across mechanical and acoustic performance, revealing that descriptors validated in compression fail under shear. First‐time comparison with trusses included. A transition from porous to resonance‐driven absorption emerges at 25% density.
Lucía Doyle, María Ángeles Navacerrada, Johan Christensen, Carlos González   +3 more
wiley   +1 more source

Planetary rover locomotion on soft granular soils - Efficient adaption of the rolling behaviour of nonspherical grains for discrete element simulations [PDF]

, 2013
In consequence of growing interests of science exploration on our solar system’s planets and moons, increased mobility demands are arising for planetary exploration vehicles.
Lichtenheldt, R., Schäfer, B., Lichtenheldt, Roy, Schaefer, Bernd   +3 more
core  

A note on the polynomial approximation of vertex singularities in the boundary element method in three dimensions

, 2008
We study polynomial approximations of vertex singularities of the type $r^\lambda |\log r|^\beta$ on three-dimensional surfaces. The analysis focuses on the case when $\lambda > -\frac 12$.
Bespalov, A, Bespalov, Alexei
core   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Revelling pore microstructure impacts on the compressive strength of porous proppant based on finite and discrete element method [PDF]

Ceramic spheres, typically with a particle diameter of less than 0.8 mm, are frequently utilized as a critical proppant material in hydraulic fracturing for petroleum and natural gas extraction.
Ge, Lei, Liao, Zijia, Li, Xiaogang, Yang, Zhaozhong, Rabiee, Hesamoddin, Xue, Qi, Shen, Chao, Wang, Hao   +7 more
core   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Continuous Stiffness Graded Metal–Ceramic Femoral Stems: UMAT‐Based Design and Finite Element Assessment

Advanced Engineering Materials, EarlyView.
Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley   +1 more source

Mechanical Behavior and Fracture Mechanisms of MXene/PVDF Nanocomponsites: In Situ Characterization and Multiscale Analysis

Advanced Functional Materials, EarlyView.
Multiscale experiments and modeling reveal how Ti3C2Tx MXene nanosheets reinforce PVDF nanocomposites. An optimal MXene loading (∼1 wt.%) nearly doubles tensile strength through efficient stress transfer, flake alignment, and crack‐deflection mechanisms, transforming ductile polymer behavior into a controlled multi‐stage fracture pathway which aligns ...
Bita Soltan Mohammadlou, James FitzPatrick, Li Meng, Kateryna Shevchuk, Ahmad Najafi, Yury Gogotsi   +5 more
wiley   +1 more source