Results 71 to 80 of about 101 (101)
Advanced Engineering Materials, EarlyView.This study designs Ta–Mo–Cr–Ti–Al refractory high‐entropy alloys with a disordered body‐centered‐cubic A2 crystal structure aiming for improved ductility, lower density, and oxidation resistance. Four alloy compositions are identified by thermodynamic calculations.
Kateryna Khanchych +7 more
wiley +1 more source
Mesoporous Silica Microspheres by Super‐Fast Alkaline Etching of Micrometer‐Sized Stöber Particles
Advanced Engineering Materials, EarlyView.Microscale silica particles are prepared along with a modified, scalable Stöber synthesis using the continuous addition of tetraethoxy silane to an ethanolic solution of ammonia with KCl. Etching with hydroxide ions at 95 °C gave porous analogs within minutes. Monodisperse particles are isolable in high yield after precipitation in ethanol.
Adrian Vaghar +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This work reveals the phase composition and quantitative morphology analysis of precipitation‐hardened Fe32Cu12Ni11Ti16Al29 complex‐concentrated alloy. The precipitates are shown to have a high coherency. Morphology transition between sphere, cuboidal, and elongated morphology is observed. Finally, the overaging behavior is captured using microhardness.
Rostyslav Nizinkovskyi +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Fe‐ and Mn‐containing AlSi alloys undergo aluminothermic reaction with Mn oxide in sessile‐drop and crucible experiments forming poor‐wetting Al2O3 while Mn enriches in the alloy. Primary Fe‐containing particles are preferentially attached to the Mn oxide.
Hanka Becker +6 more
wiley +1 more source
Comparative Study of Experimental Methods for Measuring Thermal Properties of 100Cr6 Steel Powders
Advanced Engineering Materials, EarlyView.This study investigates the thermal properties of 100Cr6 steel in both bulk and powder forms. Measuring the very low thermal conductivity typically exhibited by powders poses significant challenges. To address this, two novel measurement techniques—temperature gradient and finite laser pulse response—are introduced and evaluated by comparison with the ...
Junsheng Zhuo +8 more
wiley +1 more source
3D Bioprinting of Thick Adipose Tissues with Integrated Vascular Hierarchies
Advanced Functional Materials, Volume 35, Issue 12, March 18, 2025.An advanced 3D bioprinting technique is used here to create thick adipose tissues with a central, vessel and extensive branching. The construct is made using alginate, gelatin and collagen‐based bioinks. Flow through the complex vessel network is demonstrated as well as its successful integration with a femoral artery following implantation in a rat ...
Idit Goldfracht +5 more
wiley +1 more source
Advanced Functional Materials, EarlyView.Graded refractive index (GRI) structures are prepared from the layer‐by‐layer spray coating of the mesoporous SiO2 nanoparticles, showing high solar transparency and thermal emissivity. Under outdoor conditions, after 50 days, the GRI‐coated photovoltaics show on average 6.65 ± 1.48 °C lower than that of the non‐coated references, maintaining 80.9 ± 8 ...
Heesuk Jung +14 more
wiley +1 more source
Advanced Functional Materials, EarlyView.Transarterial Chemoembolization (TACE) may aggravate liver fibrosis. In this study, a novel oral targeting nanoemulsion is fabricated to enhance the therapeutic effect of antifibrotic drug‐pirfenidone (PFD) on fibrosis after TACE. Studies have shown that PFD nanoemulsion can enhance the oral liver targeting effect of PFD, and effectively improve the ...
Zhimei Cheng +12 more
wiley +1 more source
Advanced Functional Materials, Volume 35, Issue 12, March 18, 2025.A high‐performance n‐type element for quasi‐solid‐state thermocells has been introduced, outperforming conventional p‐type elements and showcasing the potential to harness body heat as an energy source or power embedded sensors. This advance significantly contributes to waste thermal energy harvesting and wearable technology, paving the way for self ...
Gilyong Shin +10 more
wiley +1 more source
Advanced Functional Materials, Volume 35, Issue 12, March 18, 2025.The formate pseudo‐halide anion is strategically introduced at the buried interface to stabilize the intermediate phases formed during perovskite crystallization. The controlled crystallization enhances crystallinity and alleviates tensile strain, eliminating residual PbI2 near the buried interface.
Jongdeuk Seo +12 more
wiley +1 more source