Results 171 to 180 of about 18,422 (218)

Arc welding technology for dissimilar joints

Welding International, 2003
The most widely used metal underpinning modern industry is steel (carbon steel). Low-alloy steel designed to increase the strength and heat resistance of basic carbon steel and stainless steel to offer improved corrosion resistance and oxidation resistance are extensively used in the manufacture of thermal and nuclear power plants, chemical plants, etc.
openaire   +1 more source

Mechanical and Structural Properties of Similar and Dissimilar Steel Joints

Materials Characterization, 1999
The mechanical properties of specimens from similar and dissimilar weld joints were examined. A ferritic steel (St37-2) and an austenitic stainless steel (AISI 304) were joined by the gas tungsten arc weld (GTAW) process using an austenitic filler metal.
ALSARAN, Akgün, Celik, Ayhan
openaire   +2 more sources

Evaluation of residual stresses in dissimilar weld joints

International Journal of Pressure Vessels and Piping, 2005
Abstract Dissimilar metal joints between pipes of ferritic and austenitic steels are widely used in steam generators of power plants. Failure analysis carried out on a dissimilar weld joint and a literature survey have shown that a significant number of failures have occurred in the heat affected zone (HAZ) region on the ferritic steel side of such ...
A. Joseph, Sanjai K. Rai, T. Jayakumar, N. Murugan   +3 more
openaire   +1 more source

Analysis of Nailed Joints with Dissimilar Members

Journal of the Structural Division, 1972
In order to predict the slope of the load-slip curve of two-member nailed wood joints under lateral load, a theoretical method of analysis is derived based on the theory of beams on elastic foundations. The method derived allows analysis of joints where the members are dissimilar in properties and thickness.
openaire   +1 more source

Failure Investigation of Tubular Adhesive Dissimilar Joint

Applied Mechanics and Materials, 2015
Automotive industries are looking for new implementation to deliver a good finishing product to their customer. By using adhesive material, joining against two steel can replace normal technique which is welding process. However, the strength produced by this method must be investigated. The failure investigation of ductile adhesive intended for use in
M. Faizi, W.M. Syafiq, M. Afendi, N.G. Chuen, Abu Bakar Shahriman   +4 more
openaire   +1 more source

The Joint Analysis of Direct Ratings, Pairwise Preferences, and Dissimilarities

Psychometrika, 1980
In studies involving judgments of similarity or dissimilarity, a variety of other variables may also be measured. Examples might be direct ratings of the stimuli, pairwise preference judgments, and physical measurements of the stimuli with respect to various properties.
openaire   +2 more sources

Fatigue Performance of Hybrid Adhesive Dissimilar Joint

Applied Mechanics and Materials, 2015
A research study on the fatigue performance of hybrid adhesive joints was carried out to investigate the fatigue performance of adhesive joint and hybrid adhesive joint using dissimilar material. A 3 mm thin plate of aluminium A7075 and stainless steel 304 are used as the adherend material for experimental test and the adhesive used was high ...
Ku Hafizan, Mohd Afendi, A. Logashanmugam   +2 more
openaire   +1 more source

Optimization of a Dissimilar Joint Using Additive Manufacturing

Macromolecular Symposia
AbstractThe article will explore a potential additive manufacturing approach for combining two distinct thermoplastics, ABS and PMMA. The obtained piece can be produced up of two parts: the lower half is made of ABS, while the upper part is based on PMMA.
Anamaria Feier, Mihai Brindușoiu, Dan Nițoi, Oana Roxana Chivu, Demetrius Dubic, Alin Țăpirdea, Catalina Enache   +6 more
openaire   +1 more source

Friction stir welding of dissimilar metal joints

Materialwissenschaft und Werkstofftechnik, 2019
AbstractFriction stir welding is a solid‐state welding technology, which is suitable for joining dissimilar metals such as aluminium and copper. Because the solidus temperature is typically not exceeded, the formation of intermetallic phases can be reduced when compared to fusion welding processes.
Zens, A., Zaeh, M. F., Marstatt, Roland, Haider, Ferdinand   +3 more
openaire   +1 more source

Reliability Increase of Dissimilar Steel Welded Joints

Applied Mechanics and Materials, 2014
In this paper combined Hadfield steel - stainless steel - rail steel compounds are considered. Structural studies and estimation of mechanical properties showed that using an intermediate layer of low-carbon steel with 0.2 C wt. % and 5-20 mm thick between high-carbon steel and chromium-nickel steel in the formation of welded joints increases the ...
Alexandra Chevakinskaya, Aelita Nikulina, Natalia Plotnikova   +2 more
openaire   +1 more source