Results 141 to 150 of about 7,169 (217)

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal   +2 more
wiley   +1 more source

Distribution of Electrical Resistivity in Single Carbon Fiber Filaments and Its Correlation With Tensile Modulus

open access: yesAdvanced Engineering Materials, EarlyView.
A statistical framework is applied to quantify the distribution of electrical resistivity among individual filaments of two commercially available carbon fiber types. Correlations between filament resistivity, tensile modulus, and diameter are examined and complemented by TEM analysis to provide new insight into filament‐level variability relevant for ...
Nils Wieja   +9 more
wiley   +1 more source

Engineered Mycelial Scaffolds With Tunable Ultraviolet Protection, Wettability, Thermal Stability, and Spatial Mechanics

open access: yesAdvanced Engineering Materials, EarlyView.
Fungal mycelia grown into biodegradable scaffolds and infused with titania nanoparticles show enhanced ultraviolet shielding, thermal protection, and surface nonwettability. Properties were tuned by drying methods, revealing structure–function relationships.
Juwon S. Afolayan   +2 more
wiley   +1 more source

On‐Demand Activation of Thin Alginate Shell Encapsulated Volatile Liquid for Untethered Pneumatic Soft Actuation

open access: yesAdvanced Engineering Materials, EarlyView.
Phase‐changing liquids enable untethered pneumatic actuation in soft robotics but suffer from volatility and storage challenges. This work reports a simple method to encapsulate Novec 7000 within micron‐thin alginate shells via in situ injection and ionic crosslinking.
Rayan A. M. Basodan   +3 more
wiley   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff   +9 more
wiley   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

open access: yesAdvanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa   +9 more
wiley   +1 more source

3D‐Printed Serial Snap‐Through Architectures for Programmable Mechanical Response

open access: yesAdvanced Engineering Materials, EarlyView.
A serial snap‐through architecture is realized using compact 3D‐printed von Mises truss units arranged in a staged cascade. Their geometry and boundary conditions program multistage mechanical responses with plateaux and re‐hardening regimes. An inverted‐compliance model predicts these behaviors and enables analytical design of programmable force ...
Filipe A. Santos
wiley   +1 more source

Pyramidal Structures on Yttria‐Stabilized Zirconia after High Temperature Exposure at 1500°C: New Features on an Old Material

open access: yesAdvanced Engineering Materials, EarlyView.
New features on yttria‐stabilized zirconia after exposure at 1500°C: Newly discovered pyramidal structures on an old material. After exposure at 1550°C on the cross section of YSZ new features, namely pyramidal structures are discovered. These structures grow with time, increase in numbers, appear as singularities, are often arranged in strings, and ...
Doris Sebold   +2 more
wiley   +1 more source

A Knowledge‐Based Approach for Understanding and Managing Additive Manufacturing Data

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing processes generate a large amount of data. Effectively managing, understanding, and retrieving information from this data remains a major challenge. Therefore, we propose an ontology‐based approach to integrate heterogeneous data, enable semantic queries, and support decision‐making.
Mina Abd Nikooie Pour   +5 more
wiley   +1 more source

Exploring Dipolar Dynamics and Ionic Transport in Metal‐Organic Frameworks: Experimental and Theoretical Insights

open access: yesAdvanced Functional Materials, EarlyView.
In this study, the interplay of dipolar dynamics and ionic charge transport in MOF compounds is investigated. Synthesizing the novel structure CFA‐25 with integrated freely rotating dipolar groups, local and macroscopic effects, including interactions with Cs cations are explored.
Ralph Freund   +6 more
wiley   +1 more source

Home - About - Disclaimer - Privacy