Results 81 to 90 of about 58,017,124 (282)

The cold rolling of thin brass wire

, 2022
S.362-365Today a process combining wire rolling and wire drawing is primarily employed for the production of thin wires with a diameter in the range of 1mm. Between the single process stages the material must be heat treated several times.
Schmitt, P., Konrad, T., Bark, C.
core   +1 more source

Diameter control of gold nanoparticles synthesized in gas phase using atmospheric-pressure H2/Ar plasma jet and gold wire as the nanoparticle source: Control by varying the H2/Ar mixture ratio

AIP Advances, 2017
This report describes diameter control of gold nanoparticles (AuNPs) during synthesis using an atmospheric-pressure H2/Ar plasma jet drive with pulse-modulated ultrahigh frequency, employing Au wire as the NP source material.
Yoshiki Shimizu
doaj   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

The Fault-Tolerant Control Strategy for the Steering System Failure of Four-Wheel Independent By-Wire Steering Electric Vehicles

World Electric Vehicle Journal
The drive torque of each wheel hub motor of a four-wheel independent wire-controlled steering electric vehicle is independently controllable, representing a typical over-actuated system.
Qianlong Han, Chengye Liu, Jingbo Zhao, Haimei Liu   +3 more
doaj   +1 more source

Kinematical analysis of redundant drive wire mechanisms with velocity constraint

, 2012
In this paper, we propose a new velocity constraint type for Redundant Drive Wire Mechanisms. The purpose of this paper is to demonstrate that the proposed velocity constraint module can fix the orientation of the movable part and to use the kinematical ...
Ito, K., Le, T. N., Hayashi, Yoshikatsu, Nagai, K., Koji Ito, Kiyoshi Nagai, Yoshikatsu Hayashi, Tam Nhat Le   +7 more
core   +1 more source

Rotary 3D Printing With Integrated Electroplating

Advanced Engineering Materials, EarlyView.
A rotary material extrusion platform integrates localized copper electroplating with printing and encapsulation to fabricate cylindrical polymer–metal structures containing fully embedded, low‐resistance conductive pathways that enable internal Joule heating and thermally activated shape‐memory responses.
Antonio Zagaria, Nicola Larovere, Moslem Mohammadi, Gianluca Percoco, Ali Zolfagharian, Gianni Stano   +5 more
wiley   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

The Conversion of a General Motors Cadillac SRX to Drive-By-Wire Status

, 2006
In the fall of 2004, the High Speed Autonomous Vehicle Team, a group of 16 students took on the goal of converting a vehicle to drive-by-wire status. The main goal of this project was to convert a Cadillac SRX donated by General Motors, to fully by-wire
Leppin, Leiann Kirkland
core  

Electrodeposition in Structural Lattices of Variable Architectures

Advanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon, Jingwen Zhang, Guido Musso, Alessandro F. Rotta Loria   +3 more
wiley   +1 more source

An NMPC-Based Integrated Longitudinal and Lateral Vehicle Stability Control Based on the Double-Layer Torque Distribution

Sensors
With the ongoing promotion and adoption of electric vehicles, intelligent and connected technologies have been continuously advancing. Electrical control systems implemented in electric vehicles have emerged as a critical research direction.
Xu Bai, Yinhang Wang, Mingchen Jia, Xinchen Tan, Liqing Zhou, Liang Chu, Di Zhao   +6 more
doaj   +1 more source