Results 71 to 80 of about 9,199 (313)

Integrated source reduction and treatment of metalworking fluid wastewater through induction-assisted dry hard turning of hardened SKD61 Steel

Desalination and Water Treatment
Metalworking-fluid wastewater from hard turning contains oil, suspended solids, metallic fines, and persistent organic pollutants, creating an environmental challenge for machining workshops.
Hoang Anh Tuan, Nguyen Ngoc Anh, Trieu Quy Huy   +2 more
doaj   +1 more source

Plasma EV Proteomics Identifies ECM Remodeling and Inflammatory Proteins LUM and C7 as Candidate Biomarkers in FSHD

Annals of Clinical and Translational Neurology, EarlyView.
ABSTRACT Objective Facioscapulohumeral muscular dystrophy (FSHD) is one of the most debilitating and common muscular dystrophies. Despite its severity, no approved therapy exists for FSHD patients. However, several therapeutic candidates are currently under development, and some have recently entered clinical trials, marking the need for reliable ...
Mustafa Bilal Bayazit, Chiranth K. Nagaraj, Jackson S. Newell, Kim Truc Nguyen, Xilal Y. Rima, Jacob Doon‐Ralls, Eduardo Reátegui, Jeffrey M. Statland, Rabi Tawil, Kevin M. Flanigan, Scott Q. Harper, Nizar Y. Saad   +11 more
wiley   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Toward understanding of metallurgical behaviours in dry machining of hardened steel: phase transformation and surface oxidation

Journal of Materials Research and Technology, 2019
Dry machining of hard-to-cut materials has been recognized as one of the most prospective manufacturing techniques, while involves complicated thermal and mechanical loadings inducing physical behaviours.
Binxun Li, Song Zhang, Renwei Wang, Yujie Fang   +3 more
doaj   +1 more source

What Do Large Language Models Know About Materials?

Advanced Engineering Materials, EarlyView.
If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer, Thomas Wallmersperger, Gianaurelio Cuniberti   +2 more
wiley   +1 more source

Cryogenic and conventional milling of AZ91 magnesium alloy

Journal of Magnesium and Alloys
Use of magnesium is the need of the hour due to its low density as well as its high strength-to-weight and stiffness-to-weight ratio etc. This study focuses on the effectiveness of liquid nitrogen (LN2) assisted cryogenic machining on the surface ...
Vikas Marakini, Srinivasa Pai P, Gururaj Bolar, Bhaskara P Achar   +3 more
doaj   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Experimental characterization of friction coefficients at the tool-chip-workpiece interface in cutting: Evaluation of lubrication efficiency of mineral oil [PDF]

, 2010
Collaboration avec le LTDS/ENISEThe characterization of friction coefficients at the tool-chip-workpiece interface remains an issue. This paper presents a new experimental set-up able to simulate similar tribological phenomena as the ones occurring at ...
RECH, Joël, FROMENTIN, Guillaume, DUMONT, Florian, MONDELIN, Alexandre, CLAUDIN, Christophe   +4 more
core  

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Finite Element Modeling of Microstructural Changes in Turning of AA7075-T651 Alloy and Validation [PDF]

, 2012
The surface characteristics of a machined product strongly influence its functional performance. During machining, the grain size of the surface is frequently modified, thus the properties of the machined surface are different to that of the original ...
Jawahir I. S., Umbrello, D., Rotella, Giovanna, Dillon, O.W., Umbrello D., Dillon O. W., Settineri, Luca, Jawahir, I.S.   +7 more
core