Results 101 to 110 of about 239,155 (294)
Advanced Engineering Materials, EarlyView.The share of technical thermoplastics is expected to grow further in the e‐mobility segment. In this study, a detailed temperature‐based tribological characterization of technical thermoplastics is performed. The tribological properties are discussed in terms of the dynamic mechanical properties of polymers at different ambient temperatures. A proof of
Harsha Raghuram +2 more
wiley +1 more source
Emergence and biomass accumulation in seedlings of rice cultivars irrigated with saline water
Revista Brasileira de Engenharia Agrícola e AmbientalThe objective of this study was to evaluate the performance of three rice cultivars under saline water irrigation. The experiment was carried out in full sun at the Experimental Farm of the Unilab, in Redenção, Ceará, Brazil, in January 2016.
Márcio H. da C. Freire +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Periodic submicron features are fabricated on 304 stainless steel using single and double femtosecond laser pulses. By adjusting polarization, fluence, and inter‐pulse delay, 1D and 2D nanostructures are formed. Enhanced hydrophobicity and dense surface‐enhanced Raman spectroscopy hotspots enable analyte detection down to 10−10 M with good ...
Balaji Baskar +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.In this research, ZrC coatings are evaluated against various counterprobes at the microscale using novel super‐stiff atomic force microscopy cantilevers. The chemical composition of the coating is shown to be an important factor influencing coating hardness and Young's modulus, while surface roughness, counterprobe hardness, and surface energy are the ...
Piotr Jenczyk +4 more
wiley +1 more source
Agricultural Water ManagementSeasonal water scarcity and improper cultivar selection have severely restricted the production potential of short-day onions in the dry-hot regions of southwest China. However, the appropriate irrigation regime and cultivar are still unclear. Therefore,
Yilin Li +8 more
doaj
Advanced Engineering Materials, EarlyView.Patient‐specific brain phantoms can replace animal trials, aid presurgical training, and enable in silico disease research on cerebrospinal fluid and ventricles. This study presents a method to create ventricular brain phantoms from three‐dimensional magnetic resonance images brain scans, resulting in durable, tunable, reproducible models that mimic ...
Kajal Chandraprakash Jain +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A new experimental setup, incorporating digital image correlation and infrared thermography in combination with inductive‐conductive heating for precise temperature control, is used to analyze the mechanical behavior and microstructural changes of sheet metal under complex thermomechanical test conditions that represent quench and partitioning ...
Christian Illgen +4 more
wiley +1 more source
Vacuum‐Formed Composites Based on a Polyolefin and a High Content of Biomass‐Waste Fillers
Advanced Engineering Materials, EarlyView.It is shown here that by the use of a very ductile polymer matrix, it is possible to vacuum‐form products that contain up to 25% of hard biofillers with still ductile properties. The results are promising and opens up for the use of engineered biocomposites derived from industrial side‐stream biofillers in vacuum‐formed products. A strategy to increase
Susanna K. Källbom +6 more
wiley +1 more source
Antimicrobial Titanium–Copper Alloys: The Role of Microstructure in Arc‐Melted Compositions
Advanced Engineering Materials, EarlyView.Copper‐containing titanium alloys show promise in combating orthopedic implant infections. This study explores the influence of heat treatment on Ti‐11.5Cu and Ti‐33Cu alloys, revealing that larger Ti2Cu precipitates (≈5 μm) enhance antimicrobial efficacy through increased surface contact. Results suggest contact sterilization is the primary mechanism,
Daisy Rabbitt +5 more
wiley +1 more source