Results 151 to 160 of about 788,101 (310)

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

THE KINETICS OF HEAT TRANSFER USING EXPERIMENTAL DATA OF MOISTURE EXCHANGE IN THE PROCESS OF CONVECTIVE DRYING OF THIN FLAT MATERIALS

Весці Нацыянальнай акадэміі навук Беларусі: Серыя фізіка-тэхнічных навук, 2018
The results of studies of drying of thin flat materials by method regular thermal regime are presented. The results of experimental data processing using generalized complex variables are shown. The approximate empirical equation for calculating the heat
A. I. Ol’shanskii, S. V. Zhernosek, V. I. Ol’shanskii   +2 more
doaj  

Understanding the Effect of Resistance Temperature Detector Temperature Controllers on Microstructural Alignment in Magnetic Freeze Casting

Advanced Engineering Materials, EarlyView.
The effect of temperature controllers that are commonly used in freeze‐casting is investigated in this work. Temperature controllers are observed to generate a voltage in the slurry. Microstructural alignment and ultimate compressive strength data show this voltage to interfere with the ability to align the microstructure using magnetic fields ...
Maddie A. Schmitz, Steven E. Naleway
wiley   +1 more source

Composite Electrospun Fibers Containing Optimized B‐ and Cu‐Doped Bioactive Glass Sol‐Gel Particles for Potential Soft Tissue Engineering Applications

Advanced Engineering Materials, EarlyView.
This article describes the preparation and characterization of poly(ε‐caprolactone) electrospun composite fibers incorporating sol‐gel‐derived bioactive glass particles doped with B and Cu. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared spectroscopy, contact angle, acellular bioactivity, mechanical and ...
Elisa Piatti, Marta Miola, Liliana Liverani, Paolo Sartori, Enrica Verné, Aldo R. Boccaccini   +5 more
wiley   +1 more source

Unlocking the Power of Quercetin‐Encapsulated Mesoporous Bioactive Glass Nanoparticles: A Multifunctional Approach to Bone Regeneration

Advanced Engineering Materials, EarlyView.
Mesoporous bioactive glass nanoparticles (MBGNs) are investigated for bone regeneration given their remarkable structural and functional properties. MBGNs are functionalized with Mn and Cu and incorporated with quercetin, a natural flavonoid exhibiting antioxidant, anti‐inflammatory, and antimicrobial properties.
Giovanni Lo Bello, Qaisar Nawaz, Pier Francesco Ferrari, Laura Pastorino, Roberto Raiteri, Aldo R. Boccaccini   +5 more
wiley   +1 more source

Adjustment of Coatings Morphology and Particle Distribution of Layered Silicates by Freeze‐Drying for Improved Gas Barriers

Advanced Engineering Materials, EarlyView.
Freeze‐drying of layered silicate is the key to get coatings with superior gas barrier. Freeze‐drying of layered silicates modified with dodecylamine (DDA) is a highly effective technique for the preparation of barrier pigments that significantly mitigate the permeation of oxygen, water vapor, and hydrogen through polymer films containing these ...
Joshua Lommes, Moritz Bätcher, Andrea Deißenberger, Volkmar Stenzel, Andreas Hartwig   +4 more
wiley   +1 more source

Development and Preliminary In Vivo Study of 3D‐Printed Bioactive Glass Scaffolds with Trabecular Architecture

Advanced Engineering Materials, EarlyView.
This study reports the fabrication of trabecular bioactive glass scaffolds (composition “1d”: 46.1SiO2‐28.7CaO‐8.8MgO‐6.2P2O5‐5.7CaF2‐4.5Na2O wt%) through vat photopolymerization and the relevant results from mechanical testing and in vivo implantation procedures in rabbit femora, showing great promise for bone tissue engineering applications.
Dilshat Tulyaganov, Roberta Gabrieli, Avzal Akbarov, Nigora Nigmatova, Bekhzod Khabilov, Alessandro Schiavi, Martin Schwentenwein, Enrica Verné, Francesco Baino   +8 more
wiley   +1 more source

Through air drying : Thermographic studies of drying rates, drying non-uniformity and infrared assisted drying

, 2018
The removal of water is an integral part of papermaking. The drying process is responsible for a great share of the energy used in the paper machine. Premium grade tissue products are dried by through air drying. Large volumes of natural gas are burned to heat the air drawn through the paper web to achieve the drying.
openaire   +1 more source

Is Young's Modulus a Critical Coating Property Determining Fouling‐Release Performance of Marine Coatings?

Advanced Engineering Materials, EarlyView.
The release of foulers from protective marine coatings is determined by several interrelated material properties, including the strength of Young's modulus, the flexibility of chain segments, the surface free energy, and the magnitude of hydrodynamic stress.
Johann C. Schaal, Andreas Brinkmann, Andreas Hartwig   +2 more
wiley   +1 more source

Trace Nickel Activated Biphasic Core‐CuOii/Shell‐CuOi Secondary Microspheres Enable Room Temperature Parts‐Per‐Trillion‐Level NO2 Detection

Advanced Engineering Materials, EarlyView.
An idea of designing novel sensors is proposed by creating appropriate Schottky barriers and vacancies between isomorphous Core‐CuOii/ Shell‐CuOi secondary microspheres and enhancing catalytic and spill‐over effects, and electronegativity via spontaneous biphasic separation, self‐assembly, and trace‐Ni‐doping.
Bala Ismail Adamu, Peipei Chen, Shafia Mukhtar Ibrahim, Mukhtar Lawan Adam, Attia Falak, Mokhotjwa Simon Dhlamini, Hanfu Wang, Lingxiang Jiang, Weiguo Chu   +8 more
wiley   +1 more source