Results 101 to 110 of about 237,627 (302)
Nanoindentation Criteria for Combinatorial Thin Film Libraries
Advanced Engineering Materials, EarlyView.Thin‐film material libraries are compositional spreads used for screening composition‐structure‐property relationships. Nanoindentation is often used to characterize mechanical behavior across these systems, however variations in methodology are widespread.
Andre Bohn, Adie Alwen, Andrea M. Hodge
wiley +1 more source
Effect of Heat Treatment on Performance of 2205 Base Equipment and Pipes
Engineering Reports2205 dual‐phase stainless steel is widely used in petrochemical equipment. This paper simulates welding, post‐weld heat treatment, and operation conditions of 2205 steel.
Yajun Li +4 more
doaj +1 more source
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
A new test procedure to validate tensile dynamic mechanical properties of sheet metals and alloys in automotive crash applications [PDF]
, 2008 A thin walled open channel beam subjected to a 3-point bend and constant velocity boundary condition is investigated to establish its potential to validate material performance for automotive crash applications.
Buckley, M.A., Schley, C.A., Wood, Paul
core
Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories
Advanced Engineering Materials, EarlyView.Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter +5 more
wiley +1 more source
MetalsThe volume fractions of martensite and ferrite in dual-phase steel affect its strength and plasticity. In this study, the effect of heat treatment on the structure morphology and volume fractions of martensitic and ferrite was studied in rare earth ...
Zhishen Li +5 more
doaj +1 more source
Journal of Mechanical Engineering and Sciences, 2018 Steel has wide range of applications and is used in various machinery and general metallic components. Depending on the particular application, steels with tailorable and appropriate properties are used.
Sathyashankara Sharma +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Investigation of Intercritical Annealing of Cold-rolled Ultra-high-strength Dual-phase Steel
TeshugangCold-rolled ultrahigh-strength dual-phase steel（chemical composition/%：0.220C，0.470Si， 2.500Mn，0.410Cr，0.050Al，0.020Nb） was intercritical annealed by a laboratory continuous annealing simulation machine to investigate the effect of annealing processes on
He Jinguang +6 more
doaj
Materials & Design, 2019 Copper particles that directly nucleated on the interphase precipitated TiC within the ferrite matrix were found in the CuTi bearing dual-Phase (DP) steel after a multistep heat treatment process. The formation of dual precipitates within ferrite grains
Cheng-Han Li +3 more
doaj +1 more source