Results 31 to 40 of about 302,084 (213)
Friction stir welding of duplex and superduplex stainless steels and some aspects of microstructural characterization and mechanical performance [PDF]
Materials Research, 2016 Friction stir welding was used to produce butt joints on 6 mm thick plates of UNS S32101 lean duplex stainless steel, S32205 duplex stainless steel, and S32750 and S32760 superduplex stainless steels.
Tiago Felipe de Abreu Santos +3 more
doaj +1 more source
Nuclear Engineering and Technology, 2016 Lean duplex stainless steels with 0.087 wt.% gadolinium (Gd) were inert arc-melted and cast in molds of size 10 mm × 10 mm × 20 mm. The micro-hardnesses of the rolling direction (RD), transverse direction (TD) and short transverse (ST) direction were 258.
Yong Choi +3 more
doaj +1 more source
Analysis of Corrosion and Wall Perforation in the Heat Exchanger Made of AISI 316L Stainless Steel
Materials and Corrosion, EarlyView.Elevated passivation temperature is identified as the dominant factor triggering localized corrosion and subsequent perforation of AISI 316L heat exchanger tubes. Electrochemical and complementary characterization results show that the alloy retains high resistance to general, pitting, and intergranular corrosion, indicating that failure primarily ...
Bojana Radojković +7 more
wiley +1 more source
Materials and Corrosion, EarlyView.Hydrogen‐enhanced SCC of WAAM Inconel 625 in 3.5 wt.% NaCl solution. Hydrogen charging reduces passive film stability (lower corrosion potential) and promotes pitting at Laves phase/matrix interfaces. Stress corrosion cracks propagate along Laves‐rich regions, leading to quasi‐cleavage brittle fracture.
Xu Zhang +5 more
wiley +1 more source
Single sided single pass submerged arc welding of austenitic stainless steel [PDF]
, 2007 The weld metal produced from a series of high productivity welds of 316LN austenitic stainless steel plate was examined to evaluate the effects of the use of a higher heat input process (> 2.5kJ/mm).This high heat input process was aimed at maximising ...
McPherson, N.A. +3 more
core +4 more sources
MetalMat, EarlyView.Overlap percentage governs the remelting, dilution, and solidification behavior of CMT‐WAAM AISI 308L stainless steel. Increasing overlap to 50% promotes stronger bead‐to‐bead bonding, wider transition zones, and localized hardness enhancement, with the highest hardness observed in the overlap region due to grain refinement and δ‐ferrite redistribution.
Mojtaba Karamimoghadam +4 more
wiley +1 more source
International Journal of Electrochemical Science, 2020 Steel reinforced concrete has the potential to withstand a variety of adverse environmental conditions. Nowadays, corrosion in reinforced concrete is highly regarded due to the durability of the structures.
Chunjiao Chen, Jingwu Zuo, Yingjie Wang
doaj +3 more sources
Tensile deformation behavior of duplex stainless steel before and after thermal aging by EBSD
工程科学学报, 2015 The effects of deformation degree and thermal aging on the tensile properties,phase boundaries,local strain distribution,coincidence site lattice(CSL) boundaries and orientation distribution of duplex stainless steels were investigated by electron ...
LIU Gang +3 more
doaj +1 more source
steel research international, EarlyView.Niobium cathodic cage duplex treatment is applied to VP20TS steel to evaluate the influence of surface roughness and temperature on coating performance. Results show that higher temperatures promote thicker nitride layers and increased microhardness, while finer surface preparation enhances adhesion and wear resistance, revealing optimal conditions for
Alan Bruno Costa Cardoso +6 more
wiley +1 more source
Mechanical and thermal induced phase transformations in superduplex stainless steel [PDF]
, 2000 The aim of this work is to study the microstructural changes in SAF 2507 type superduplex stainless steel due to heat treatments and mechanical fatigue process.
Dobránszky, János +2 more
core +1 more source